Uniden UBC785XLT Reverse Mode, Channel Step Selection, Mute On/Off, Receiving Mode Selection

Page 49

UB343ZH_UBC785XLT_OM_0622 6/22/06 3:01 PM Page 45

Reverse Mode

This key will allow you to observe the reverse frequency of the repeater. While pressing RVRS, the standard pair frequency will be displayed. For a list of the standard pair frequencies, refer to the table "Reverse List" in the Appendix. If the frequency that you have chosen does not have an offset frequency, the display will indicate ERROR and NO REVERSE.

Channel Step Selection

You can set frequency step, 5 kHz - 100 kHz or Auto in Chain search frequency. The default receive mode should be the proper mode setting in almost all cases. You may wish to set some VHF channels for NFM mode, depending on any adjacent channel interference problems. WFM is typically only used for broadcast frequencies, such as TV audio or FM radio.

See STEPS in "Menu Description" for details.

Mute On/Off

To manually turn ON the Mute function, press and hold MUTE until MUTE ON is displayed. You will not hear any audio. To turn it OFF, press and hold MUTE again.

Receiving Mode Selection

You can also set the receiving mode, AM or NFM in Chain Search mode.

See MODE in "Menu Description" for details.

Frequency and Channel Tuning with the VFO Control

The VFO knob can be used for stepping frequencies or through memory channels.

To switch the setting for the VFO control, press the VFO. This will change modes from Channel to Frequency or Frequency to Channel.

1.In scan hold mode, when the setting for the VFO is channel, rotate the VFO to move up (to step up through channels) or down (to step down through channels).

2.In Chain Search mode, when the setting for the VFO is frequency, rotate the VFO to move up to step up through frequencies sequentially or to down to step down through frequencies. To change the step, you will need to go into the Chain Search menu and adjust the step for the desired memory location.

Remember! When you set Additional Features through the menu screen, you can also use or instead of rotating the VFO.

Also instead of pressing E, you can press the VFO control.

45

Image 49
Contents A N N E R UB343ZHUBC785XLTOM0622 6/22/06 301 PM Contents UB343ZHUBC785XLTOM0622 6/22/06 301 PM Introduction 15kHz Offset UB343ZHUBC785XLTOM0622 6/22/06 301 PM VFO/SELECT Push Front and Rear ViewIcon Description UBC785XLT Shortcuts Press Menu Important Notice What is Searching? What is Scanning?Terminology Feature Highlights Information on the Internet Where to Obtain More InformationIncluded with Your Scanner Package Connecting an Antenna SetupMounting an Antenna Optional AntennaMounting the Scanner in Your Vehicle Typical Mounting MethodsApplying Power for Vehicle Installation Applying Power Using Standard AC Power Desktop InstallationConnecting an External Speaker Connecting an EarphoneConnecting the Tape Recorder Connecting the Clone CableListening Safely RememberBasic Operation Setting the SquelchTurn the Scanner On Understanding the Menu System Menu Description and Numeric Keypad Equivalents 6RECORD Allows you to change the brightness of the display 9BANK TAG Programming Storing Frequencies into Channels in Menu Mode001 001 855.0000 FMC1000 010 512.0000 FM0000.0000 Transfer Frequencies 001 855.0000 NFM Alpha TAGStoring Alpha Tags Programming Tips Beep AlertAssigning the Beep Alert to a Channel To directly access a specific channel Scan Hold FeatureScanning BankSetting the Delay Mode for Frequency RF Attenuation Feature001 141.5000 FM Uniden Group a Lockout in Hold ModeChannel Lockout Restoring a Locked-out Channel Lockout in Scanning ModeRestoring All Locked-out Channels 005 512.0000 FM 010 1240.0000 FMPriority Scan Changing the Priority ChannelSearching Setting a Search RangeSrch 12.5k Srch 12.5k 1240.0000 FM Range 25cm Amateur Grp Search Hold FeatureStarting Chain Search Data SkipFrequency Skip Srch 12.5k 1240.0000 NFM Range C004Storing Search Frequencies 12--56 Squelch SQ Mode001 FM Bank Auto StoringFor Search mode, select 1SERVICE Option / Chain Search 001 FM DCS Bank 003003 FM DCS Uniden Group a 001 512.0000 FM BankUsing Aircraft Service Search Air Service SearchAir Service Search Skip Changing the stepRemote Interface PC Control ModeTo connect Scanner to PC To program your scannerStart Remote Mode and Change Transfer Speed Clone ModeSpeed 39600 bps 419200 bps PC Control Parameter To connect the Scanner to Scanner Clone Master Unit Slave Unit Dimmer Additional FeaturesEnter Lock Key Beep OptionReceiving Mode Selection Reverse ModeFrequency and Channel Tuning with the VFO Control Channel Step SelectionCare and Maintenance Resetting the Scanner TroubleshootingSpecifications Glossary of Terms UB343ZHUBC785XLTOM0622 6/22/06 301 PM DCS Tone Code Ctcss Frequency List HzUBC785XLT Flow Charts Scan Option System Option Dimmer 1HIGH / 2MEDIUM / 3OFF Screen Mask Declaration of Conformity Uniden Corporation All rights reserved UBZZ01343ZZ0
Related manuals
Manual 60 pages 30.57 Kb