Panasonic TH-32LHD7UX manual PC Input Terminals connection, Signal Names for D-sub 15P Connector

Page 10

Connections

PC Input Terminals connection

COMPUTER

AUDIO

PC IN

	Conversion adapter	Less than	Ferrite core (large size)
	(if necessary)	3" 15/16	(supplied) D-sub 15p
		(10 cm)	(supplied) D-sub 15p
			RGB
			PC cable
	Less than	Ferrite core	Less than
	3" 15/16	(Small size)	3" 15/16
	(10 cm)	(supplied)	(10 cm)
		Audio	Stereo plug
			Stereo plug
	Connect a cable which matches
	the audio output terminal on the computer.
Installing the ferrite core (Small size)
1	2	3
		Open
	Pull back the tabs		Press the cable
	(in two places)		through and close

Installing the ferrite core (Large size)

1

2

3

Open

Pull back the tabs (in two places)

Press the cable through and close

Notes:

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to “NORMAL”, and 1,366 × 768 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

Signal Names for D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	GND (Ground)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	GND (Ground)	9	NC (not connected)	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents Operating Instructions LCD Display Model No. TH-32LHD7UXEnglish Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice Trademark CreditsWhen using the LCD Display Safety PrecautionsTY-WK32LR1S AC Power Supply Cord SetupIf problems occur during use Accessories Supplied AccessoriesRemote Control Batteries Speakers ConnectionsAC cord ﬁxing Signal Names for D-sub 15P Connector PC Input Terminals connectionSerial Terminals connection Installing the ferrite core Large sizeCommand Communication parametersConnecting the AC cord plug to the LCD Display Power on / OFFConnecting the plug to the Wall Outlet Selecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2 PCBasic Controls On OFF Advanced Settings On-Screen Menu DisplaysTime / Power OFF Time On TIME/ Power OFF TimeNormal Zoom Full Aspect ControlsNormal Full Clock Phase Adjusting Picture Position / SizeClock Phase RGB/PC in modePress to change input signal Press to swap main picture and sub pictureStandard Picture AdjustmentsAuto DynamicAdvanced Settings Bass Sound AdjustmentMute TrebleSelect the area of the image to be enlarged Digital ZoomDisplay the Operation Guide Select the magniﬁcation required for the enlarged displayPress to exit from Present Time Setup Present Time SetupPress to set up Present Time of DAY Button ForwardPower on Time / Power OFF Time SET UP TimerDisplay the SET UP Timer Screen Press to select Power OFF FunctionCustomizing the Input labels Reduces power consumptionPower Save Standby Save Power Management Auto Power OFF Press to select on or OFF On Off3D Y/C Filter For Ntsc AV images SET UP for Input SignalsComponent / RGB in Select SelectPulldown / Video NR Color System / Panasonic AutoColor System FREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Displays the H Horizontal / V Vertical frequenciesPress and hold till the Shipping menu is Press to display the SET UP menuShipping condition Press to select YESTroubleshooting LCD Display panelSignal name Horizontal Vertical Input signal can be displayedApplicable input signals for PC Input D-sub 15P ∗ Mark When Multi ScreenAccessories Supplied SpeciﬁcationsPanasonic Broadcast & Television Systems Company Executive Ofﬁce Customer’s RecordPanasonic Broadcast & Television Systems Company Panasonic Canada Inc