Panasonic TH-32LHD7UX manual Connections, Speakers, AC cord ﬁxing

Page 9

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

	AV	SPEAKERS
SLOT 1	SLOT 2PC INSERIAL	SPEAKERS

		Terminals (L)
	SPEAKERS	AC cord connection (see page 12)
	Terminals (R)	AC cord connection (see page 12)
	Terminals (R)
		– AC cord ﬁxing

1
2	1
	1
	2

1.Open the clamper.

Clamper

2. I n s e r t t h e A C c o r d	3. Slide up the clamper and ﬁx	4. Insert the point of the
and close the clamper	the AC cord plug securely.	fixed clamper into the
securely.	When loosen	small hole on the lower
	the clamper:	r i g h t o f
		t h e b a c k
		c o v e r a s
		necessary.
AC cord

Note: The power plug in the illustration may not be the type ﬁtted to your set.

–Cable ﬁxing bands

Secure any excess cables with bands as required.

Pass the attached cable ﬁxing band through the clip as shown in the ﬁgure.

To secure cables connected to Terminals, wrap the cable ﬁxing band around them then pass the pointed end through the locking block, as shown in the ﬁgure.

While ensuring there is sufﬁcient slack in cables to minimize stress (especially in the power cord), ﬁrmly bind all cables with the supplied ﬁxing band.

To tighten:	To loosen:

Pull	Push the catch

1

2	Pull

Optional Terminal Board insert Slots (covered)

R AUDIO L	VIDEO IN	VIDEO OUT	R	AUDIO L	VD HD PR/CR/R PB/CB/B Y/G	AUDIO
IN			R	AUDIO L

		AV		COMPONENT/RGB IN
S VIDEO IN		AV		COMPONENT/RGB IN

SLOT1	SLOT2	PC IN	SERIAL

From EXTERNAL monitor terminal on Computer (see page 10)

From SERIAL Terminal on Computer

(see page 11)

9

Image 9

Contents LCD Display Model No. TH-32LHD7UX Operating InstructionsEnglish Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits Canadian NoticeSafety Precautions When using the LCD DisplayTY-WK32LR1S Setup AC Power Supply CordIf problems occur during use Accessories Accessories SuppliedRemote Control Batteries Connections SpeakersAC cord ﬁxing PC Input Terminals connection Signal Names for D-sub 15P ConnectorCommand Installing the ferrite core Large sizeSerial Terminals connection Communication parametersPower on / OFF Connecting the AC cord plug to the LCD DisplayConnecting the plug to the Wall Outlet Initial selections Selecting the input signalSelecting the On-Screen Menu Language INPUT1 INPUT2 PCBasic Controls On OFF On-Screen Menu Displays Advanced SettingsOn TIME/ Power OFF Time Time / Power OFF TimeAspect Controls Normal Zoom FullNormal Full Clock Phase Adjusting Picture Position / SizeClock Phase RGB/PC in modePress to swap main picture and sub picture Press to change input signalAuto Picture AdjustmentsStandard DynamicAdvanced Settings Mute Sound AdjustmentBass TrebleDisplay the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magniﬁcation required for the enlarged displayPress to set up Present Time of DAY Present Time SetupPress to exit from Present Time Setup Button ForwardDisplay the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Power OFF FunctionPower Save Standby Save Power Management Auto Power OFF Reduces power consumptionCustomizing the Input labels Press to select on or OFF On OffComponent / RGB in Select SET UP for Input Signals3D Y/C Filter For Ntsc AV images SelectColor System / Panasonic Auto Pulldown / Video NRColor System Sync Setting RGB sync signalFREQ. kHz / V-FREQ. Hz Displays the H Horizontal / V Vertical frequenciesShipping condition Press to display the SET UP menuPress and hold till the Shipping menu is Press to select YESLCD Display panel TroubleshootingApplicable input signals for PC Input D-sub 15P ∗ Mark Input signal can be displayedSignal name Horizontal Vertical When Multi ScreenSpeciﬁcations Accessories SuppliedPanasonic Broadcast & Television Systems Company Panasonic Broadcast & Television Systems Company Customer’s RecordExecutive Ofﬁce Panasonic Canada Inc