Panasonic TH-32LHD7UX manual Setup, AC Power Supply Cord, If problems occur during use

Page 7

Safety Precautions

WARNING

Setup

Do not place the LCD Display on sloped or unstable surfaces.

• The LCD Display may fall off or tip over.

Do not place any objects on top of the LCD Display.

•If water spills onto the LCD Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the LCD Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

• Doing so may cause the LCD Display to overheat, which can cause fire or damage to the LCD Display.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 1 31/32” (5 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/8” (6 cm) or more at the rear.

AC Power Supply Cord

The LCD Display is designed to operate on 120 V AC, 50/60 Hz.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

•Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the LCD Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the LCD Display, unplug the power cord immediately.

•Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the LCD Display, if the LCD Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

• A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

MAINTENANCE

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water to which a small amount of neutral detergent has been added, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the LCD Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operating Instructions LCD Display Model No. TH-32LHD7UXEnglish Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits Canadian NoticeWhen using the LCD Display Safety PrecautionsTY-WK32LR1S AC Power Supply Cord SetupIf problems occur during use Accessories Supplied AccessoriesRemote Control Batteries Speakers ConnectionsAC cord fixing PC Input Terminals connection Signal Names for D-sub 15P ConnectorCommunication parameters Installing the ferrite core Large sizeCommand Serial Terminals connectionConnecting the AC cord plug to the LCD Display Power on / OFFConnecting the plug to the Wall Outlet INPUT1 INPUT2 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageBasic Controls On OFF On-Screen Menu Displays Advanced SettingsOn TIME/ Power OFF Time Time / Power OFF TimeNormal Zoom Full Aspect ControlsNormal Full RGB/PC in mode Adjusting Picture Position / SizeClock Phase Clock PhasePress to swap main picture and sub picture Press to change input signalDynamic Picture AdjustmentsAuto StandardAdvanced Settings Treble Sound AdjustmentMute BassSelect the magnification required for the enlarged display Digital ZoomDisplay the Operation Guide Select the area of the image to be enlargedButton Forward Present Time SetupPress to set up Present Time of DAY Press to exit from Present Time SetupPower OFF Function SET UP TimerDisplay the SET UP Timer Screen Press to select Power on Time / Power OFF TimePress to select on or OFF On Off Reduces power consumptionPower Save Standby Save Power Management Auto Power OFF Customizing the Input labelsSelect SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesPulldown / Video NR Color System / Panasonic AutoColor System Displays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzPress to select YES Press to display the SET UP menuShipping condition Press and hold till the Shipping menu isLCD Display panel TroubleshootingWhen Multi Screen Input signal can be displayedApplicable input signals for PC Input D-sub 15P ∗ Mark Signal name Horizontal VerticalSpecifications Accessories SuppliedPanasonic Broadcast & Television Systems Company Panasonic Canada Inc Customer’s RecordPanasonic Broadcast & Television Systems Company Executive Office
Top Page Image Contents