Panasonic TH-50PF9UK Safety Precautions / Maintenance, Setup, AC Power Supply Cord

Page 7

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

•Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

Transport only in upright position!

•Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

•Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

•Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

•A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water to which a small amount of neutral detergent has been added, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model No. TH-50PF9UK High Definition Plasma DisplayOperating Instructions EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits When using the Plasma Display Safety PrecautionsAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupAccessories Supplied AccessoriesRemote Control Batteries DVI-D COMPONENT/RGB ConnectionsSpeakers AC cord fixingPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Basic format for control data CommandSerial Terminals connection Communication parametersDVI-D connection Component / RGB connection & RGB signal R, G, BDVI-D Input Connector Signal NameConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet OFF Basic ControlsBasic Controls On-Screen Menu Displays Advanced SettingsOn Time / Power OFF Time / Power OFF TimeOn-Screen Menu Displays INPUT1 INPUT2 INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageNormal Zoom Full Aspect ControlsNormal Full POS / V-SIZE / DOT Clock / Clock Phase Adjusting POS. /SIZEPixel Mode Size Adjusting POS. /SIZEClock Phase POSMulti PIP Sub screen Main screen Advanced PIPCinema Picture AdjustmentsStandard DynamicPicture Adjustments Advanced SettingsMute Sound AdjustmentReturn to normal display quit Digital Zoom Digital ZoomDisplay the Operation Guide Select the magnification required for the enlarged displayPress to set up Present Time of DAY Present Time SetupPress to select Set Press to select Power on Function SET UP TimerDisplay the SET UP Timer Screen Press to select Power on Time / Power OFF TimeNegative / Scroll selection Mode selectionStart setting Screensaver For preventing after-imagesScreensaver For preventing after-images Setup of Screensaver TimePress to display the SET UP menu Reduces screen after-imageOFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input Press to select on or OFF SET UP for Multi DisplayHow to setup Multi Display Group of 4 2 × Group of 9 3 × Group of 16 4 ×Display Number locations for each arrangement Examples SET UP for Multi DisplayPress to select Seam Hides Video Press to select OFF, onID Cancellation Seam Hides Video SettingID Remote Control Function ID remote control button operationComponent RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesColor System SET UP for Input SignalsColor System / Panasonic Auto Pulldown / Video NRDisplays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzFunction Options AdjustmentsOff Initial VOL Sets normal volume Level Options AdjustmentsMenu & Enter NormalizationShipping condition Plasma Display panel TroubleshootingDVI-D DVI-D/COMPONENT/RGB/PC input signalsTH-50PF9UK SpecificationsLimits and Exclusions Panasonic Canada Inc Customer’s RecordPanasonic Broadcast & Television Systems Company Executive Office
Top Page Image Contents