Panasonic DP-1510P manual Job Memory, To Store a Job in Memory, To Recall a Job Stored in Memory

Page 22

Creative Features

Job Memory

■Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a later time.

JOB MEMORY

PRESS M1,M2 TO STORE.

To Store a Job in Memory

#Set up the copy job to be stored in memory, by first selecting each function you wish the copier to perform.

$Press the MEMORY IN (F2) key.

%Press the M1 (F3) or M2 (F4) key.

RECALL JOB MEMORY

To Recall a Job Stored in Memory

&Place the Original

(Press the M1 (F3) or M2 (F4) key. The stored contents will be displayed.

)Press START

	NOTE	CStored job(s) will not be deleted even if the power switch is turned Off.
	NOTE	CWhen storing a new job into programmed memory, the previously stored job will be

		overwritten.

Image 22

Contents Options Before StartingEnglish Others Important Information Model and Serial NumberOperation Chart Common Features and UsageEnergy Star Table of Contents Options Problem SolvingOthers For Your Safety PrecautionsLaser Safety Handling Toner and Paper VentilationInstallation For U.KControl Panel Interrupt Key, Memory in Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Copy Size KeyCopying the Same Size Originals Basic CopyFull Size Copying $Select Exposure ControlSelect the Copy Copying with Preset RatiosReduction or Enlargement Copying Paper Tray keyPress Cursor G or F keys to select Zoom Ratio Zoom CopyingZoom Select OriginalCopying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides Press Start1 Copy Creative FeaturesProcedure PressCopy Place the Press Originals page Copy KeyPlaten Press BOOK, Edge Or Margin keyKey Operation Sided/1-Sided Copy For DP-2010EBook \ Press 2-Sided \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010ESided Copy key Book \ 2 Copy For DP-2010E Place the Original on the PlatenTo Recall a Job Stored in Memory Job MemoryTo Store a Job in Memory $Press the Memory in F2 keySort Copy Sort ModeSort Copy From Platen Glass onlyEnergy Saver Mode Other FeaturesEnergy Saver/Interrupt Mode Sleep ModeSkyshot Mode Digital Skyshot ModeManual Skyshot Mode Platen Upper- left cornerNext Combined Function TableRemarks Job Memory RetrievalUsing Function Modes to Change the Initial Copy Modes FunctionModes Function Initial Setting General FunctionsCopier Settings General Functions for Key Operator Copier Settings for Key Operator Press the Function key Function SettingChanging the Auto Exposure Setting Proceed as FollowsChanging the Paper Size Function Setting for Key OperatorFunctions Stopper Guide a Paper Guide b IndicatorPaper SizeDepartment Counter Select the Department Counter Mode Page Accessories ComponentsADF DA-AS180 / i-ADF DA-AR201 FeaturesAutomatic Document Feeder ComponentsOriginal OperationPlace Inappropriate OriginalsAdding Paper J Problem SolvingSheet Paper Tray Remove the Waste Toner Container by Adding the Toner and Replacing Waste Toner Container ?Open the Front Cover Slowly pulling it towards the left asProblem Solving Removing a Misfed Paper Paper Misfeed LocationsPaper Exit Area Remove the misfed paperHot Paper Entry/Transport AreaOpen the Right Cover Remove the misfed paper HeatedOpen the Right Cover ADU Area For DP-2010E onlyClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Check Action TroubleshootingBefore Calling Service Unit Does Not OperateLight Copies Add Toner Warning IndicatorMarked Copies User Error Codes U Code As a rule, clean weeklySpecifications DP-1510P/1810P/2010E Copier2nd/4th Paper Feed Module DA-DS182 ADF DA-AS180ADF DA-AR201 3rd Paper Feed Module DA-DS183For Network Printing Options and SuppliesFor Printer SuppliesPage Page For Service, Call