Panasonic PT-AE3000U manual Projection method, Front leg adjusters and throwing angle, Setting up

Page 15

Setting up

Projection method

You can use the projector with any of the following 4 projection methods. To set the desired method in the projector, See “INSTALLATION” on page 44.

Setting on a desk/floor and projecting from front

Setting on a desk/floor and projecting from rear

INSTALLATION: FRONT/DESK

Mounting on the ceiling and projecting from front

INSTALLATION: REAR/DESK

Mounting on the ceiling and projecting from rear

Getting Started

INSTALLATION: FRONT/CEILINGINSTALLATION: REAR/CEILING

NOTE:

•A translucent screen is required for rear projection.

•When mounting the projector on the ceiling, the optional ceiling mount bracket (ET-PKE2000, ET-PKE1000S) is required.

•See “Ceiling mount bracket safeguards” on page 56.

Front leg adjusters and throwing angle

You can screw up/down the front leg adjusters to control the angle of the projector for adjusting the throwing angle. See “Positioning the image” on page 22.

NOTE:

•Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly.

•If keystone distortion occurs, see “KEYSTONE” on page 39.

•Screw up the front leg adjusters, and an audible click will be heard as the limit.

ENGLISH - 15

Image 15

Contents Operating Instructions Dear Panasonic Customer Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Model Number PT-AE3000U Trade NameContents Lens Control ContentsMenu Navigation Picture menuPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Do not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Use only the specified batteriesLiquid crystal panel Projector may be subject to electromagnetic interferenceOrder to get the best picture quality Do not touch the surfaces of the lens with your bare handsPower cord secure lock AccessoriesRemote control for Safety cable Lens cover Power cordAbout Your Projector Remote controlProjector body About Your ProjectorTop and front view Component About Your Projector Back and bottom viewComputer HdmiSetting up Calculation methods for screen dimensionsScreen size and throw distance Mounting on the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift dialsLens shift and positioning Horizontal shift100% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting example Component IN/S-VIDEO Connecting example Hdmi IN/COMPUTERConnect the power cord to a wall outlet Switching the projector on/offPower cord ConnectingPower indicator Switching the projector on/offPower indicator informs you the status of the power Switching on the projector Switching off the projectorPress the power or Enter button Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeAdjusting the image Remote control operationManaging the lens control settings Switching the picture modeRemote control operation Loading a saved settingSwitching the aspect ratio Adjusting the signal condition with a waveformContrast G/CONTRAST B Adjustment exampleAdjusting with luminance options Adjusting with RGB optionsManaging stored logs Setting your own color profileAdjusting the selected color Create a new profileLoading saved profiles Saving a log setting as a profileDeleting the saved profiles Changing the profile namesCapturing an image Resetting to the factory default settingsSwitching the input signal Using the assigned function as shortcutDisplaying the main menu Adjusting with the bar scale itemsMenu Navigation Navigating through the MenuMenu Navigation Main menu and sub-menuLanguage Lens Control Picture menu Waveform Monitor Color TemperatureSplit Adjust Dynamic IrisNR Noise Reduction Adjusting the image in a split windowStandard xvYCC ColorMemory Edit Signal ModeMemory Save Memory LoadDOT Clock Clock PhasePosition menu PositionFIT Component signalsPosition menu Aspect ratio options and projection example ZoomKeystone Auto SetupWSS Over ScanLens Memory Save Adjust ZOOM/FOCUS, H-AREA PositionZOOM/FOCUS Lens Memory LoadSelect Lens Memory Name Change and press the Enter button You can edit named lens memory settingsLens Memory Edit Area PositionAssignable functions Underlined item is factory default settingButton Blank functionOption menu Sleep InstallationHigh Altitude Mode Lamp PowerTemp indicator Temp and Lamp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeAttaching the top cover Troubleshooting Dots *1 MHz KHz List of compatible signalsTechnical Information Quality *2Serial terminal Control commands Technical Information Communication settingsInquiry commands Specifications Hdmi VideoComputer ComponentCeiling mount bracket safeguards Installing the safety cableLoop twice Loop once Dimensions Trademark acknowledgementsUnit mm Index Index

Related manuals

Manual 60 pages 29.63 Kb