Panasonic PT-AE3000U manual Important Safety Notice, Declaration of Conformity, Panasonic

Page 3

Important Safety Notice

WARNING:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computers or peripheral devices. Any unauthorized changes or modifications to this equipment will void the users authority to operate.

Important Information

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Center

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

WARNING: Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

 

Declaration of Conformity

Model Number:

PT-AE3000U

Trade Name:

Panasonic

Responsible party:

Panasonic Corporation of North America

Address:

One Panasonic Way, Secaucus, New Jersey 07094

Telephone number:

(888) 411 - 1996

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information on Disposal in other Countries outside the European Union

These symbols are only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

ENGLISH - 3

Image 3
Contents Operating Instructions Dear Panasonic Customer Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Model Number PT-AE3000U Trade NameContents Lens Control ContentsMenu Navigation Picture menuPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Do not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Use only the specified batteriesLiquid crystal panel Projector may be subject to electromagnetic interferenceOrder to get the best picture quality Do not touch the surfaces of the lens with your bare handsPower cord secure lock AccessoriesRemote control for Safety cable Lens cover Power cordAbout Your Projector Remote controlProjector body About Your ProjectorTop and front view Component About Your Projector Back and bottom viewComputer HdmiSetting up Calculation methods for screen dimensionsScreen size and throw distance Mounting on the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift dialsLens shift and positioning Horizontal shift100% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting example Component IN/S-VIDEO Connecting example Hdmi IN/COMPUTERConnect the power cord to a wall outlet Switching the projector on/offPower cord ConnectingPower indicator Switching the projector on/offPower indicator informs you the status of the power Switching on the projector Switching off the projectorPress the power or Enter button Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeAdjusting the image Remote control operationManaging the lens control settings Switching the picture modeRemote control operation Loading a saved settingSwitching the aspect ratio Adjusting the signal condition with a waveformContrast G/CONTRAST B Adjustment exampleAdjusting with luminance options Adjusting with RGB optionsManaging stored logs Setting your own color profileAdjusting the selected color Create a new profileLoading saved profiles Saving a log setting as a profileDeleting the saved profiles Changing the profile namesCapturing an image Resetting to the factory default settingsSwitching the input signal Using the assigned function as shortcutDisplaying the main menu Adjusting with the bar scale itemsMenu Navigation Navigating through the MenuMenu Navigation Main menu and sub-menuLanguage Lens Control Picture menu Waveform Monitor Color TemperatureSplit Adjust Dynamic IrisNR Noise Reduction Adjusting the image in a split windowStandard xvYCC ColorMemory Edit Signal ModeMemory Save Memory LoadDOT Clock Clock PhasePosition menu PositionFIT Component signalsPosition menu Aspect ratio options and projection example ZoomKeystone Auto SetupWSS Over ScanLens Memory Save Adjust ZOOM/FOCUS, H-AREA PositionZOOM/FOCUS Lens Memory LoadSelect Lens Memory Name Change and press the Enter button You can edit named lens memory settingsLens Memory Edit Area PositionAssignable functions Underlined item is factory default settingButton Blank functionOption menu Sleep InstallationHigh Altitude Mode Lamp PowerTemp indicator Temp and Lamp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeAttaching the top cover Troubleshooting Dots *1 MHz KHz List of compatible signalsTechnical Information Quality *2Serial terminal Control commands Technical Information Communication settingsInquiry commands Specifications Hdmi VideoComputer ComponentCeiling mount bracket safeguards Installing the safety cableLoop twice Loop once Dimensions Trademark acknowledgementsUnit mm Index Index
Related manuals
Manual 60 pages 29.63 Kb