Panasonic PT-D6000, PT-D5000 Digital Cinema Reality, Input Resolution, Blanking, Clamp Position

Page 22

ADVANCED MENU

Remote control

See “Navigating through the menu” on page 15.

See “Main menu and Sub-menu” on page 12.

DIGITAL CINEMA REALITY

You can improve the vertical resolution for PAL (or SECAM) 576i, NTSC 480i, 1080/50i or 1080/60i signals. Press I H to cycle through the options.

Setting range

Models	Vertical	Horizontal

PT-DZ6710/PT-DZ6700	0 - 599	0 - 959

PT-DW6300	0 - 399	0 - 639

PT-D6000/PT-D5000	0 - 383	0 - 511

INPUT RESOLUTION

Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour, vertical stripes or stuck pixels appear on the screen. Press F G to select the required option to change, and I H to change the value. The initially displayed values vary according to the selected input signal.

Settings

	Detects PAL (or SECAM) 576i, 1080/50i, NTSC
AUTO	480i and 1080/60i input signals and change the
	setting properly.
OFF	Deactive
	Detects only PAL (or SECAM) 576i and 1080/50i
25p FIXED	signals, and adjust the vertical resolution of the
	image to 2:2 pulldown.
	Detects only NTSC 480i and 1080/60i signals,
30p FIXED	and adjust the vertical resolution of the image to
	2:3 pulldown.

NOTE:

•25p FIXED or 30p FIXED setting with signals that is not 2:2 pulldown may result low quality.

TOTAL DOTS

DISPLAY DOTS

TOTAL LINES

DISPLAY LINES

NOTE:

•The vertical stripes will not appear on the all white signal image.

•The picture may be distorted during the adjusting operation, but this is not a fault.

•The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN.

•With PT-DW6300/PT-D6000/PT-D5000, automatic adjustment is not available if signals having a dot clock frequency of more than 150 MHz are supplied.

BLANKING

You can perform fine adjustments for blanking if noise appears at the ends of the screen or the image protrudes out of the screen during image projection using a VCR and so on. Press F G to select the edge to adjust, and I H to move the inner edge of the blank.

UPPER	LOWER
LEFT	RIGHT

CLAMP POSITION

When black part of the image is losing its colour or becomes green, you can adjust to the best colour. Press I H to change the value.

Setting range: 0 to 255

NOTE:

• Available with signals from RGB 1 IN/RGB 2 IN only.

I: Moves the inner edge of the blank area to outside.

H: Moves the inner edge of the blank area to inside.

ENGLISH - 22

Image 22

Contents PT-DZ6700 PT-DW6300 PT-D6000 PT-D5000 Contents Projection distance Setting upScreen size and throw distance Height of the projection areaSetting up Projection distance by projection lens PT-DZ6710/PT-DZ6700Setting up PT-DW6300PT-D6000/PT-D5000 Through ratio FixedPT-DW6300 PT-DZ6710/PT-DZ6700PT-D6000/PT-D5000 Screen Geometric adjustmentScreen Side viewFront leg adjusters and throwing angle Connections Pin assignments and signal namesBefore connection to the projector Connecting with Video IN/S-VIDEO Connecting example ComputersConnecting example AV equipment ConnectionsMenu Navigation Main menu and Sub-menuDisplay Option Signal List Projector SetupMenu Navigation Test PatternSecurity Navigating through the menu Adjusting with the bar scale itemsOperating procedure Displaying the main menuPicture menu System Daylight View White GainNoise Reduction SharpnessAspect Position menuShift Aspect ratio options Zoom Clock Phase Geometry Position menu Vertical Keystone Lens Throw RatioKeystone Digital Cinema Reality Input ResolutionSetting range BlankingEdge Blending Adjusting with colour markersAdjusting Edge Blending Selecting gamma levelRaster Position Adjusting brightness around borderline of the image areaBright adjustment right Marker Projection rangeDisplay Option menu SDI Auto SetupDVI-D ON-SCREEN DisplayFreeze Back ColorStartup Logo Side by SideHigh Altitude Mode Projector Setup menuInstallation Projector IDREMOTE2 Mode Lamp PowerStandby Mode Lamp SelectStatus Filter Counter ResetNo Signal SHUT-OFF Function ButtonSave ALL Users Data Service PasswordDate and Time InitializeSelect Test Pattern menu Test PatternPress I H to select the required test pattern Signal List and SUB Memory List Managing the list and the registered dataSignal List Managing the sub memory listDisplay Setting Security Password ChangeSecurity Password Security menuRemote Controller Menu Lock PasswordControl Device Setup Menu LockNetwork Control Network SetupNetwork menu Network StatusNetwork connection Technical InformationLAN terminal Administrator mode Accessing with the web browserChange password Technical InformationDetail control User modeBasic control User accountAdjust clock Detailed set upNetwork config Authentication set upMail set up Mail report sample Error report sampleProjector status Error informationStatus Click DetailPJLink security authorization Control commandsPJLinkTMprotocol Serial terminal Pin assignments and signal namesCommunication settings ConnectionCable specifications Technical Information Basic formatOther Remote 2 in terminalPin assignments and control ContactSide by Side function signal combination table Side by Side function signal combination tableRestoring the Menu Lock Password to default Movie signalsTrademark acknowledgements Index Index Combination table