|
|
|
|
|
|
|
|
|
|
|
|
|
| Technical Information |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Basic format |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| The data streaming from the computer will |
| STX | Command |
| : |
| Parameter | ETX |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| start with STX, and proceed to Command, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Start | byte |
|
| 1 byte |
|
| End | Parameter and end with ETX. You can | |||||
| 3 bytes | 1 byte - | ||||||||||||
| (02h) |
|
|
|
| (03h) | add the required parameter. | |||||||
|
|
|
|
|
|
| 4 bytes | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command.
If sending multiple commands, check that a response has been received from the projector for one command before sending the next command.
When a command which does not require parameters to be sent, the colon (:) is not required.
If an incorrect command is sent from the personal computer, the ER401 command will be sent from the projector to the personal computer.
Control commands
Command | Control contents |
|
| Remarks |
| |
|
| In standby mode, all commands other than the PON command are | ||||
PON | Power ON | ignored. |
|
|
| |
|
| The PON command is ignored during lamp ON control. | ||||
|
| If a PON command is received while the cooling fan is operating after | ||||
POF | Power OFF | the lamp has switched off, the lamp is not turned back on again straight | ||||
|
| away in order to protect the lamp. |
| |||
|
| Parameter: |
|
|
| |
IIS | Input signal | VID = VIDEO IN | SVD = | |||
selection | RG1 = PC IN |
| YUV = COMPONENT IN | |||
|
| |||||
|
|
|
| HDM = HDMI IN | ||
OMN | Menu screen | The menu screen will be displayed. |
| |||
|
|
| ||||
OEN | ENTER | Use this command to accept and to activate items selected in the on- | ||||
screen menus. |
|
| ||||
|
|
|
| |||
OBK | RETURN | Use this command to return to a previous menu screen or to clear the | ||||
menu screen. |
|
|
| |||
|
|
|
|
| ||
OCU/OCD/ | Navigation buttons | OCU = F button | OCL = I button | |||
OCL/OCR | OCD = G button | OCR = H button | ||||
| ||||||
|
|
|
|
|
| |
OST | Returning to the | Use this command to return the setting to the factory default. (page 23) | ||||
default setting | ||||||
|
|
|
|
| ||
|
| The picture being projected will be paused. |
| |||
OFZ | Freeze function | Parameter: |
|
|
| |
|
| 0 = OFF |
| 1 = ON | ||
|
| Use this command to momentarily turn off the picture. | ||||
OSH | Shutter function | Operation will be switched between ON and OFF each time the command | ||||
is sent. Do not switch operation ON and OFF after only short periods of | ||||||
|
| |||||
|
| time. |
|
|
| |
OVM | MAIN | Use this command to display an item in the PICTURE menu. (page 28) | ||||
|
|
| ||||
VS1 | Aspect ratio | The aspect ratio will be switched each time the command is sent. | ||||
selection | (page 23) |
|
|
| ||
|
|
|
| |||
|
| Parameter: |
| NOR=NORMAL | ||
| Picture mode | NAT=NATURAL | ||||
VPM | DYN=DYNAMIC | CN1=CINEMA1 | ||||
selection | ||||||
| CN2=CINEMA2 | CN3=VIVID CINEMA | ||||
|
| |||||
|
| VID=VIDEO (page 28) |
|
| ||
|
| Setting the duration of time to turn off the power automatically. | ||||
OOT | SLEEP selection | 0 = OFF | 1 = 60 min. | 2 = 90 min. | 3 = 120 min. 4 = 150 min. | |
|
| 5 = 180 min. | 6 = 210 min. | 7 = 240 min. | (page 23) | |
Appendix
ENGLISH - 43