Panasonic PT-LB30E, PT-LB30NTE manual Adjusting the position, Position, DOT Clock, Clock Phase

Page 41

Adjusting the position

When an RGB signal is being input, press the AUTO SETUP button first to initiate automatic positioning. If the optimum setting is not obtained when “AUTO SETUP” is carried out, adjust by the following procedure.

Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment.

When an RGB/YPBPR signal is being input

POSITION

POSITION

 

DOT CLOCK

32

CLOCK PHASE

16

ASPECT

4:3

RESIZING

ON

FRAME LOCK

OFF

STANDARD

 

SELECTENTER RETRN

When an S-VIDEO/VIDEO signal is being input

POSITION

 

POSITION

 

ASPECT

4:3

RESIZING

ON

STANDARD

 

 

 

SELECT

 

ENTER

RETRN

POSITION

Moves the picture position.

Press the ENTER button to display the “POSITION” screen.

Press the I or H button to move the picture horizontally.

Press the F or G button to move the picture vertically.

POSITION H 64

V32

DOT CLOCK

(RGB only)

Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the

Ior H button to adjust so that any such noise is minimised.

CLOCK PHASE

(RGB/YPBPR only)

Adjust the “DOT CLOCK” setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable.

NOTE:

BIf signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the “DOT CLOCK” and “CLOCK PHASE” adjustments are carried out.

Adjustments and settings

ENGLISH-41

Image 41
Contents Model No. PT-LB30NTE LCD Projector Commercial UseModel number PT-LB30NTE / PT-LB30E Dear Panasonic CustomerPreparation Contents Do not remove the cover or modify it in any way Precautions with regard to safetyDo not overload the mains socket Insert the mains plug securely into the mains socket Do not handle the mains plug with wet handsDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorDo not cover the air inlet port or the air outlet port Do not use the projector in a bath or showerDo not look into the lens while the projector is being used Do not put your weight on this projector Insulate the battery using tape or similar before disposalAlways disconnect all cables before moving the projector Do not place any heavy objects on top of the projectorAccessories Be sure to attach the lens cover before moving the projector Before useDo not touch the surfaces of the lens with your bare hands Order to get the best picture qualityScreen LampLocation and function of each part Leg adjuster buttons L/RLens cover Projection lens Remote control signal receptor $ % # Connector panel $ Air outlet portRGB2 IN/1 OUT connector pages 20, 21 $ RGB1 in connector pages 20Video in connector pages 22 Audio in L-R connectors for S-VIDEO/VIDEOPower input socket AC + RGB Audio 1IN/2IN connectors pages 20$ Lamp indicator # RGB Input indicatorTemp indicator MenuVolume +/- buttons Auto Setup button pages 25Illumination sensor Input buttonsProjection methods Setting-upProjection distances Projector positionConnections Connecting to computerConnecting to video equipment Connecting to video equipment Insert the battery holder Preparation for the remote control unit$Press the Power button Turning on the powerTurn on the power of all connected devices Before turning on the powerAdjusting the angle Press the input select button to select the input signalAdjusting the size Adjusting the focusPress the Power button Turning off the powerProjector status Direct power off functionPower button on the projector Press the Auto Setup button Press the Freeze button Pausing a picture FreezeTurning off the picture and sound momentarily Shutter Remote control unit functions during D.ZOOM digital zoom Adjusting the volume VolumePress the Volume +/- button Enlarging the picture D.ZOOMPress the Index Window button Displaying two screens Index WindowMenu screens On-screen menusKeystone Keystone correctionAdjustments and settings Index Window function Shutter function Volume adjustmentPosition menu Language menuMenu operation guide STD Returning a setting to the factory defaultContrast Bright Color Tint Sharpness Color Temp Select Enter RetrnVertical keystone distortion correction only Correcting keystone distortionVertical OperationPicture Mode Adjusting the pictureBright ContrastColor TintDaylightview Mode Auto OFFDaylightview Signal Mode Still ModeTV-SYSTEM TV-SYSTEM Auto NtscClock Phase Adjusting the positionPosition DOT ClockAspect Auto AspectFrame Lock ResizingChanging the display language Auto Signal Option settingsOSD Auto SearchRGB2 Select Sxga ModeRGB/YPBPR BlackboardDESK/CEILING Lamp PowerFAN Control Lamp RuntimeAuto POW.OFF Power MemoryControl KEY Amend Passwd Setting up the security functionInput Passwd Text Change Text DisplayNetwork DefaultName Change WEB ControlRemedy Lamp indicator Temp indicatorLamp Power Lamp indicatorCleaning Cleaning and replacing the air filterReplacement procedure Air filter should be cleaned every 100 hours of useReplacing the lamp unit Lamp unit replacement periodLamp unit replacement procedure Control KEY Auto POW.OFF Disable Lamp PowerOption Back Color FRONT/REAR Front DESK/CEILINGBefore calling for service Cleaning and maintenance PAL60/SECAM SpecificationsOptions Remote control unitAppendix List of compatible signalsProjection dimensions calculation methods Pin assignments and signal names Using the Serial connectorCommunications settings ConnectionCommand Control Remarks Contents Control commandsCable specifications Trademark acknowledgements Dimensions