Panasonic PT-LB30E Option Back Color, FRONT/REAR Front DESK/CEILING, Lamp Power, Func, Select

Page 57

'Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws.

NOTE:

BBe sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.

(Connect the mains lead.

)Press the POWER button so that a picture is projected onto the screen.

NOTE:

BIf the mains lead was disconnected during projection when the projector was used the last time, projection will start after the mains lead is connected (when “POWER MEMORY” in the “OPTION” menu is set to “ON”). Refer to page 48 for details.

*Press the MENU button to display the “MAIN MENU”, and then press the F or G button to select “OPTION”.

MENU

KEYSTONE

PICTURE

POSITION

INDEX WINDOW

SHUTTER

VOLUME

LANGUAGE

OPTION

SECURITY

NETWORK

SELECTENTEREXIT

+Press the ENTER button to display the “OPTION” menu, and then press the F or G button to select “LAMP RUNTIME”.

OPTION

		▲
BACK	COLOR	BLUE

FRONT/REAR		FRONT

DESK/CEILING		DESK

FAN CONTROL		STANDARD

LAMP	POWER	HIGH

LAMP	RUNTIME	1820H

FUNC	1	DAYLIGHT

CONTROL KEY		ON

AUTO POW.OFF DISABLE

POWER	MEMORY	ON

SELECT		RETRN

,Press and hold the ENTER button for approximately 3 seconds.

OPTION

		▲
BACK	COLOR	BLUE

FRONT/REAR		FRONT

DESK/CEILING		DESK

FAN CONTROL		STANDARD

LAMP	POWER	HIGH

TIME	RESET [POWER OFF]

FUNC	1	DAYLIGHT

CONTROL KEY		ON

AUTO POW.OFF DISABLE

POWER	MEMORY	ON

SELECT		RETRN

The “LAMP RUNTIME” will change to “TIME RESET [POWER OFF]”.

NOTE:

BIf the MENU button is pressed, the lamp time resetting screen will be cancelled.

-Turn off the power and disconnect the mains lead. This will reset the cumulative usage time for the lamp unit to “0”. Refer to page 26 for details on how to turn off the power.

Care and maintenance

ENGLISH-57

Image 57

Contents Model No. PT-LB30NTE LCD Projector Commercial UseModel number PT-LB30NTE / PT-LB30E Dear Panasonic CustomerPreparation Contents Precautions with regard to safety Do not overload the mains socketDo not remove the cover or modify it in any way Insert the mains plug securely into the mains socket Do not handle the mains plug with wet handsDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorDo not use the projector in a bath or shower Do not look into the lens while the projector is being usedDo not cover the air inlet port or the air outlet port Do not put your weight on this projector Insulate the battery using tape or similar before disposalAlways disconnect all cables before moving the projector Do not place any heavy objects on top of the projectorAccessories Be sure to attach the lens cover before moving the projector Before useDo not touch the surfaces of the lens with your bare hands Order to get the best picture qualityScreen LampLeg adjuster buttons L/R Lens cover Projection lens Remote control signal receptorLocation and function of each part $ % # Connector panel $ Air outlet portRGB2 IN/1 OUT connector pages 20, 21 $ RGB1 in connector pages 20Video in connector pages 22 Audio in L-R connectors for S-VIDEO/VIDEOPower input socket AC + RGB Audio 1IN/2IN connectors pages 20$ Lamp indicator # RGB Input indicatorTemp indicator MenuVolume +/- buttons Auto Setup button pages 25Illumination sensor Input buttonsProjection methods Setting-upProjection distances Projector positionConnections Connecting to computerConnecting to video equipment Connecting to video equipment Insert the battery holder Preparation for the remote control unit$Press the Power button Turning on the powerTurn on the power of all connected devices Before turning on the powerAdjusting the angle Press the input select button to select the input signalAdjusting the size Adjusting the focusPress the Power button Turning off the powerDirect power off function Power button on the projectorProjector status Press the Auto Setup button Pausing a picture Freeze Turning off the picture and sound momentarily ShutterPress the Freeze button Remote control unit functions during D.ZOOM digital zoom Adjusting the volume VolumePress the Volume +/- button Enlarging the picture D.ZOOMPress the Index Window button Displaying two screens Index WindowMenu screens On-screen menusKeystone Keystone correctionAdjustments and settings Index Window function Shutter function Volume adjustmentPosition menu Language menuMenu operation guide STD Returning a setting to the factory defaultContrast Bright Color Tint Sharpness Color Temp Select Enter RetrnVertical keystone distortion correction only Correcting keystone distortionVertical OperationPicture Mode Adjusting the pictureBright ContrastColor TintMode Auto OFF DaylightviewDaylightview Signal Mode Still ModeTV-SYSTEM TV-SYSTEM Auto NtscClock Phase Adjusting the positionPosition DOT ClockAspect Auto AspectFrame Lock ResizingChanging the display language Auto Signal Option settingsOSD Auto SearchRGB2 Select Sxga ModeRGB/YPBPR BlackboardDESK/CEILING Lamp PowerFAN Control Lamp RuntimePower Memory Control KEYAuto POW.OFF Setting up the security function Input PasswdAmend Passwd Text Change Text DisplayNetwork DefaultName Change WEB ControlRemedy Lamp indicator Temp indicatorLamp Power Lamp indicatorCleaning Cleaning and replacing the air filterReplacement procedure Air filter should be cleaned every 100 hours of useReplacing the lamp unit Lamp unit replacement periodLamp unit replacement procedure Control KEY Auto POW.OFF Disable Lamp PowerOption Back Color FRONT/REAR Front DESK/CEILINGBefore calling for service Cleaning and maintenance PAL60/SECAM SpecificationsOptions Remote control unitAppendix List of compatible signalsProjection dimensions calculation methods Pin assignments and signal names Using the Serial connectorCommunications settings ConnectionControl commands Cable specificationsCommand Control Remarks Contents Trademark acknowledgements Dimensions