Nortel Networks 5000i manual Cabling

Page 34

•Attach one end of the Hobbes to Catgut cable assembly (flat, 40-pin polarized cable) to the Hobbes board{ XE "Hobbes board" \i }.

•Set the Catgut board into the PCI slot—two slots to the right of th Hobbes board— making certain that the Catgut board (and the Hobbes board) are firmly seated.

•Attach the other end of the Hobbes to Catgut cable to the Catgut board.

4.Ensure that the high density ribbon cable connector connecting the Hobbes board to the Catgut board is fully seated.

5.Replace the cover on the computer.

6.Open the rear panel doors and place the computer on the shelf. The front of the computer must face the front of the scanner.

Cabling

In preparation for{ XE "Standalone installation:Cabling" } cabling, NCS Pearson recommends that you do the following:

•Set the computer on the back lip of the shelf during cable installation so that the back of the computer is tilted up. This provides easier access to the computer's ports.

•Uncoil all cords and cables, separate them, and lay them out on the floor.

The following cabling instructions are for a standalone configuration{ XE "Cabling:Standalone configuration" }. Refer to Figures 3-4 and 3-5, and Table 3-1 at the end of this chapter.

1.Install the computer power cord.

•Attach the power cord connector to the back of the computer.

•Ensure that the other end is plugged into the scanner's power strip.

2.Complete installation of the 25-pin straight through cable - the PRTCON board (for the optional printer) to the back of the computer.

•One end of this cable is already attached to the PRTCON board.

•Connect the other end (free end) to the back of the computer.

3.Complete installation of one 6-pin DIN cable - the KEMCON board (for the keyboard) to the back of the computer.

•One end of this cable is already attached to the KEMCON board.

•Connect the other end (free end) to the back of the computer in the keyboard port.

4.Complete installation of the other 6-pin DIN cable - the KEMCON board (for the mouse) to the back of the computer.

•One end of this cable is already attached to the KEMCON board.

•Connect the other end (free end) to the back of the computer in the mouse port.

5.Complete installation of the 5 BNC/15-pin DIN cable - from the bulkhead (for the monitor) to the back of the computer.

•One end (5 BNC end) is already attached to the bulkhead.

•Connect the other end (15-pin DIN) to the back of the computer.

Connect this cable to the 15-pin connector on the video card in the first expansion

Page 22

5000i Scanner Installation Guide

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Installation Guide For the 5000i Scanner Page Installation Guide For the 5000i Scanner For Users in the United States Tab/Rev Date Description Revision LogIii 5000i Scanner Installation Guide Preface System Component Manual Title5000i Scanner Installation Guide Table of Contents Viii 5000i Scanner Installation Guide Introduction Introduction5000i Scanner Installation Guide Overview of the Scanner XE Scanner, 5000iOverview Scanner OverviewScanner Overview Scanner Installation Guide Technical Support for Hardware Problems Customer SupportTechnical Support for Software Problems Scanner Overview Hardware Scanner InstallationPreparation SoftwareChecking the Installation Site InstallationScanner Installation 5000i Scanner Installation Guide Spares XE Spares kit, contents Installing the ScannerUnpacking the Scanner Grounding Power NoiseCondition Description Dedicated Ground 5000i Scanner Installation Guide Scanner Installation Site Power Wiring Recommendations Power Frequency Limits Voltage Limits Other Data +12V Boost Power Supply Location of the Power SuppliesPage Location of the Power Supplies Scanner Installation Installation of Computer and Other Peripherals Shut DownInstallation Standalone InstallationComputer XE Standalone installationComputer Computer and Peripherals InstallationCabling Work Table Monitor XE Standalone installationMonitorMonitor and Keyboard Board/Connector Relationship Standalone Board/Connector LocationsNetwork Installation XE Scanner, 5000iNetwork configuration Computer5000i Scanner Installation Guide Cabling Monitor XE Network installationMonitor Keyboard and Mouse XE Network installationKeyboard and mouse Network Board/Connector Locations Internal Cable Connections XE Internal cable connectionsComputer and Peripherals Installation Cable Part XE Cable part numbers Numbers and Connections Part Number Description Type PC ConnectionOptional Equipment Network Printer XE Network installationPrinter optionalSystem Printers Bar Code Reader Computer and Peripherals Installation System Verification XE CheckoutSystem verification Scanner CheckoutSystem Software RequirementsScanner Checkout 5000i Scanner System Software Scanner Checkout 5000i Scanner Installation Guide Index Index5000i Scanner Installation Guide
Top Page Image Contents