Rockford Fosgate R150-2 manual Troubleshooting, Procedure 1 Check Amplifier for proper connections

Page 9

TROUBLESHOOTING

NOTE:If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1: Check Amplifier for proper connections.

Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue.

1.Check in-line fuse on battery positive cable. Replace if necessary.

2.Check fuse(s) on amplifier. Replace if necessary.

3.Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.

4.Verify there is 9 to 14.4 Volts present at the positive battery and remote turn-on cable.Verify quality connections for both cables at amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Protect light is on.

1.If the Protect light is on, this is a sign of a possible short in the speaker connections. Check for proper speaker connections and use a volt/ohm meter to check for possible shorts in the speaker wiring.Too low of a speaker impedance may also cause Protect to light.

Procedure 3: Check Amplifier for audio output.

1.Verify good RCA input connections at stereo and amplifier. Check entire length of cables for kinks, splices, etc.Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

2.Disconnect RCA input from amplifier. Connect RCA input from test stereo directly to amplifier input.

Procedure 4: Check Amplifier if you experience Turn-on Pop.

1.Disconnect input signal to amplifier and turn amplifier on and off.

2.If the noise is eliminated, connect the REMOTE lead of amplifier to source unit with a delay turn-on module.

OR

1.Use a different 12 Volt source for REMOTE lead of amplifier.

Procedure 5: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2.Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3.Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4.Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5.Have alternator and battery load tested by your mechanic.Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents R150-2 Introduction Table of ContentsContents of Carton Safety InstructionsR150-2 Design FeaturesMounting Locations Installation Installation ConsiderationsEngine Compartment Trunk MountingBattery and Charging InstallationWiring the System Passenger Compartment MountingInstallation Operation Adjusting Gain Adjusting Crossover FrequencyPunch Bass Procedure 1 Check Amplifier for proper connections TroubleshootingSpecifications subject to change without notice SpecificationsLimited Warranty Information Length of WarrantyTable DES Matières FrançaisContenu DE Lemballage Consignes DE SécuritéParticularités Techniques Emplacements DE Montage Installation Considérations Concernant L’INSTALLATIONCompartiment moteur Montage dans le coffreBatterie ET Charge Câblage DU SystèmeMontage dans l’habitacle Fusible Réglage DE LA Fréquence DU Filtre Passif Fonctionnement Réglage DU GainProcédure 2 Le voyant de protection ou thermique est allumé DépannageLes spécifications sont sujettes à changements sans préavis CaractéristiquesInformations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónContenido DE LA Caja Instrucciones DE SeguridadCaracterísticas DEL Diseño Lugares DE Montaje Instalación Consideraciones Para LA InstalaciónCompartimento del motor Instalación en el maleteroBateríay Carga InstalaciónCableado DEL Sistema Instalación en la cabina de pasajerosInstalación Punch Bajos Funcionamiento Ajuste DE GananciaSolución DE Problemas Especificaciones Información Sobre LA Garantía Limitada Duración de la garantíaInhaltsverzeichnis EinleitungInhalt DES Kartons SicherheitshinweiseDesigncharakteristiken Befestigungsstellen Einbau EinbauüberlegungenMotorraum Einbau im KofferraumBatterie UND Aufladung EinbauVerkabelung DES Systems Einbau im InnenraumSource Unit Betrieb Lautstärke Gain Einstellen CROSSOVER-FREQUENZ EinstellenPunch Bässe Fehlerbeseitigung OderOrer Die technischen Daten können sich ohne Ankündigung ändern Technische DatenInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCaratteristiche DEL Design Posizionamento Installazione Considerazioni SULL’INSTALLAZIONEScompartimento del motore Montaggio nel bagagliaioBatteria E Caricamento InstallazioneCablaggio DEL Sistema Montaggio nello scampartimento passeggeriLinea con una fonte da 12 volt per attivare l’amplificatore Funzionamento Regolazione DEL Guadagno Regolazione Della Frequenza DI IncrocioPunch Basso Oppure INDIVIDUAZIONE/RIPARAZIONE GuastiSpecifiche soggette a modiche senza preavviso SpecificheInformazioni Inerenti Alla Garanzia Limitata Lunghezza della garanziaRockford Fosgate

R150-2 specifications

The Rockford Fosgate R150-2 is a powerful and versatile car amplifier that embodies the brand's commitment to high-quality audio performance. With its impressive specifications and advanced technology, the R150-2 is designed to enhance the sound system of any vehicle, catering to both casual listeners and audiophiles alike.

One of the standout features of the R150-2 is its robust power output. The amplifier delivers 75 watts RMS per channel into a 4-ohm load, and up to 150 watts RMS at 2 ohms. This makes it ideal for driving a variety of aftermarket speakers or enhancing the power of factory-installed systems. The R150-2 is designed to ensure clarity and detail across the audio spectrum, allowing users to enjoy their favorite music with enhanced depth and richness.

The R150-2 employs Class AB technology, which is known for providing excellent sound quality with minimal distortion. This means that users can enjoy loud volumes without sacrificing audio fidelity. The amplifier also features a variable high-pass crossover, allowing users to tailor the frequency response to suit their listening preferences and the specific characteristics of their speakers.

Another notable aspect of the R150-2 is its user-friendly design. The amplifier is equipped with a remote gain control, which allows for easy adjustments to the output level from the driver's seat. This feature is particularly useful for fine-tuning the system without having to reach for the amplifier directly.

Durability and reliability are also key characteristics of the R150-2. It comes with a cast aluminum heatsink, ensuring effective heat dissipation, which is crucial during prolonged use. The amplifier also features short-circuit and thermal protection, safeguarding the unit from damage while providing peace of mind to users.

Installation of the R150-2 is straightforward, thanks to its compact size and easy-to-follow wiring diagram. Its design includes a high-quality connector for power and speaker outputs, ensuring solid and reliable connections.

Overall, the Rockford Fosgate R150-2 is a formidable choice for anyone looking to upgrade their car's audio system. With its powerful output, sound-enhancing technologies, and user-friendly features, it stands out as a top contender in the amplifier market, making it an excellent investment for sound enthusiasts seeking to elevate their in-vehicle listening experience.
Top Page Image Contents