Tektronix 750 User safety summary, Terms in manual

Page 8

User safety summary

Terms in manual:

Caution: Conditions that can result in damage to the product.

Warning: Conditions that can result in personal injury or loss of life.

Use proper power source: Do not operate this product from a power source that applies more than the voltage specified. To avoid fire hazard, use only the power cord specified for this product. In hospital applications, grounding reliability can only be achieved by the use of a hospital grade power cord, and the equipment is connected to an equivalent receptacle marked “hospital only” or “hospital grade.”

Operation of product: There are no user-serviceable parts inside the product. Avoid electric shock by contacting a qualified service technician to repair the product. Do not operate without the covers and panels properly installed. Do not operate in an atmosphere of explosive gases or flammable mixtures.

Safety instructions: Read all installation instructions carefully before you plug the product into a power source.

Terms on product:

CAUTION: A personal injury hazard exists that may not be apparent. For example, a panel may cover the hazardous area. Also applies to a hazard to property including the product itself.

DANGER: A personal injury hazard exists in the area where you see the sign.

Care of product: Disconnect the power plug by pulling the plug, not the cord. Disconnect the power plug if the power cord or plug is frayed or otherwise damaged, if you spill anything into the case, if product is exposed to any excess moisture, if product is dropped or damaged, if you suspect that the product needs servicing or repair, and whenever you clean the product.

Ground the product: Plug the three-wire power cord (with grounding prong) into grounded AC outlets only. For protection against electric shock, this product is classified Class I, and Type B where applicable.

Location of product: Place the printer in a well ventilated area.

Image 8

Contents L O R P R I N T E R Phaser 750 Color Printer User Guide Page Page Warranty Printer WarrantyConsumables Warranty Page User safety summary Terms in manualSymbols as marked on product Contents Phaser 750 Color Printer Tektronix Supplies and Accessories SuppliesHigh Capacity Toner Cartridges Standard Toner CartridgesFuser Roll and Cleaning Pad FuserImaging Unit Transfer KitTektronix Color Laser Labels Tektronix Professional Printing PaperTektronix Transparency Film Paper Trays Transparency TraysPrinter Station Internal Hard DriveAdditional memory Automatic Duplex/Lower Tray AssemblyPhaserShare Token Ring Network Card Print Quality Modes Fast ColorFeatures TekColor Color CorrectionsPaper Tips Paper TipsLetterhead Supported page sizes and image area Trays Paper and Transparency TraysPaper Tray Transparency Tray Loading Paper or Transparency Tray Maximum Tray Level Multi-Purpose Tray Multi-Purpose TrayOverview Thin Normal Thick Loading the Multi-Purpose Tray Tektronix Transparency Tektronix Glossy Coated Paper Tektronix Premium Cover PaperTektronix Color Laser Label PaperEnvelope #10 Paper 2nd SideHeavy Paper Special Media Loading Special MediaTektronix Transparencies 0236-13 Printing #10 Envelopes EnvelopesEnvelope Guidelines for envelope printing Printing on Tektronix Color Laser Labels At the printerApplication LabelsGuidelines for printing on labels Automatic 2-Sided Printing Sided Prints0632-28 Windows NT4 Start/Settings/Printers PC Drivers Windows 95/ WindowsClick Properties Click Print on 2-Sides optionMacintosh Drivers LaserWriter Select Print on Both SidesManual 2-Sided Printing From the Multi-Purpose Tray Side3 4 5 6 3 4 5 6 Troubleshooting Print Quality Replace the Toner CartridgePrint Quality AgentaSymptom Problem in one color only Solution Adjust the color density Replace the Toner Cartridge of the color that has problemsSymptom Problem in all four colors Solution Replace Imaging Unit, or Fuser, or Fuser RollSymptom All four colors are solid black Symptom All four colors are extremely fadedSolution Symptom Pieces of print image missing all four colors Replace FuserMedia Jams Preventing media jamsJam-Wrong Media JamsJam at a Jam at B Lower Tray Assembly Only Jam at C Remove the jammed media from the Fuser Jam at D Open the front door and the right side door Jam at E Jam at Multi-Purpose Tray Jam at Duplex Unit Re-insert the Duplex Unit into the printer’s upper slot Printer CD-ROM Getting HelpFront panel Help button PhaserLink Software Tektronix web siteTekSMART Knowledge Base Getting HelpCustomer Support Centers Other online servicesColor Connection Color Density Controlling Color DensityPrint and use the Color Reference Color Density Printed on recycled paper