Asante Technologies IC36240 user manual Configuring Link Type, Configuring an Edge Port

Page 50

Configuring Link Type

Use the following interface mode command to configure port link-type:

Switch(config)# interface eth1 Switch(config-if-eth1)#spanning-treelink-type{point-to-pointshared}

By default, the link type is determined from the duplex mode of the interface: a full-duplex port is considered to have a point-to-point connection; a half-duplex port is considered to have a shared connection.

To return the switch to its default setting, use the no spanning-treelink-typeinterface configuration command.

Configuring an Edge Port

Use the following interface mode command to configure port link type:

Switch(config)# interface eth1

Switch(config-if-eth1)#spanning-treeedge-port

The default setting is no edge port configuration.

To return the switch to its default setting, use the no spanning-treeedge-portinterface configuration command.

Configuring Port Path Cost

Use the following interface mode command to configure port path cost:

Switch(config)# interface eth1

Switch(config-if-eth1)#spanning-treepath-cost<path-cost>

The default values for path cost is determined by the operating port speed:

For ports operating in 1000Mb speed, the path cost is 20000

For ports operating in 100Mb speed, the path cost is 200000

For ports operating in 10Mb speed, the path cost is 2000000

To return the switch to its default setting, use the no spanning-treepath-costinterface configuration command.

Configuring Port Priority

Use the following interface mode command to configure port priority:

Switch(config)# interface eth1 Switch(config-if-eth1)#spanning-treeport-priority<port-priority>

For <port-priority>, the range is 0–240 in increments of 16; the default is 128. The lower the number, the higher the priority.

To return the switch to its default setting, use the no spanning-treeport-priorityinterface configuration command.

50

Asante IntraCore IC36240

User’s Manual

Image 50
Contents IntraCore IC36240 Series Layer 2+ Gigabit Ethernet Switch User’s Manual IntraCore IC36240Table of Contents Password Service Password-Encryption Snmp Configuration Commands Trunk Ieee 802.1q Technical Support and Warranty Features IntroductionPackage Contents Front and Back Panel DescriptionsLEDs LEDManagement and Configuration Console InterfaceSafety Overview Hardware Installation and SetupInstallation Overview Power Requirements Installing into an Equipment RackRecommended Installation Tools Environmental RequirementsEquipment Rack Guidelines Installing the Optional External Power SupplySFP Mini Gbic Ports 1 10/100/1000BaseT Ports Cabling Procedures Connecting PowerConnecting to the Network Gigabit Ethernet Ports Cabling Procedures Pin Number Pair Number & Wire ColorsAsante IntraCore IC36240 Initial Software Setup Connecting to a ConsoleConnecting to a PC User Access Verification PasswordEnable Password Passwords and Privileges CommandsPrivileges Commands Password Service Password-EncryptionUsername Command Login SecurityConfiguring an IP Address Password and login CommandsSetting a Default IP Gateway Address Restoring Factory DefaultsSystem Boot Parameters Switchconfig# ip default-gatewayAccess Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Document ConventionsPrivileged Top Privileged Exec Mode Command Show ? PurposeGlobal Configuration Mode Command Exit End Ctrl-Z Purpose Switch# configureInterface Configuration Mode Spanning-Tree Configuration ModeSpanning-tree mst configuration Advanced Features Supported within the Command ModeVlan Configuration Mode Command Help Purpose Example of Context Sensitive HelpChecking Command Syntax Switch# configure ?Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Keystrokes/Command PurposeKeystrokes Purpose Moving Around on the Command LineCompleting a Partial Command Name Editing Command Lines That Wrap Scrolling Down a Line or a Screen Redisplaying the Current Command LineDeleting Entries Keystrokes Transposing Mistyped CharactersControlling Capitalization Switch# clock ? Managing the System and Configuration FilesSetting the System Clock Switch# clock set 092930 28 January Switch# reload crSpecifying the Hostname Changing the PasswordTesting Connections with Ping Tests Enabling the System LogConfiguring from the Terminal Managing Configuration FilesDisplaying the Operating Configuration Switch# show running-configCopying Configuration Files to a Network Server Newname# copy running-config startup-configSwitch# copy startup-config ? Switch# copy running-config tftp//192.168.0.1/my-config Switch# copy running-configSwitch# copy running-config Tftp Access Control Configuring SnmpAuthentication Switch# copy tftp//192.168.123.59/my-confg running-configSupport Create or Modify Access Control for Snmp CommunitySecurity Levels Command Purpose Snmp-server community string view Establish the Contact and Location of the Snmp AgentConfiguring Spanning Tree Snmp Configuration CommandsSpanning Tree Parameters Spanning-tree mst?Port Priority Spanning Tree Port ConfigurationRapid Spanning Tree Protocol Rstp Port Path CostRapid Convergence Configuring Switch/Bridge PrioritySwitchconfig# spanning-tree priority priority Enabling Rapid Spanning TreeConfiguring Port Path Cost Configuring Link TypeConfiguring an Edge Port Configuring Port PriorityMultiple Spanning-Tree MST Configuring Vlan VlanShow mac-address-table Switchconfig# mac-address-table aging-timeMAC Address Table Class Address or Range Status Configuring IPAssign IP Addresses to Switch Establish Address Resolution Define a Static ARP CacheIgmp Overview Configuring IgmpManaging IP Multicast Traffic Forwarding Unknown Multicast PacketsCommand Purpose Ip igmp query-max-response-time Using Access ListsSwitchconfig-if-veth1#ip igmp query-interval Host-query messagesUsing a Classification ACL Asante IntraCore IC36240 Create a Standard Access List Switchconfig# mac access-list standard Create a MAC Access ListCreate an Expanded Access List Access-list 101 deny tcp ? Access-list 101 ?Access-list 101 deny ? Access-list 101 deny tcp 192.168.123.0 0.0.0.255 ?Access-list ? Creating an Access List with a NameApplying an Access List to an Interface Access-list standard ?Configuring Common Access Lists Switchconfig# access-list 110 permit udp any any eqAccess-list 101 deny ip any any Vlan Configuration Creating or Modifying a VlanDeleting a Vlan Switch# show vlanSwitchconfig-vlan#port-member delete eth Trunk Ieee 802.1q Static AccessVlan Port Membership Modes Command Purpose Switchconfig# vlan dot1q tag native Switchconfig# endMonitoring Weighted Fair Queuing Lists Quality of Service ConfigurationConfiguring Weighted Fair Queuing Priority QueuingDefining the Priority List Configuring Traffic Shaping for an InterfaceTraffic Shaping Monitoring Priority Queuing ListsMonitoring the Traffic Shaping Configuration Configuring Rate LimitConfiguring Traffic Shaping for an Access List Generic Traffic Shaping ExampleAsante IntraCore IC36240 Configuring the Switch Using the GUI Main Configuration MenuInformation Screens Front Panel Information ScreenAssign IP Addresses to Switch General Information ScreenClass Address or Range Status Port Configuration Menu Individual Port Configuration ScreenAsante IntraCore IC36240 Press go Spanning Tree Protocol Configuration STP Port Configuration Global STP Bridge Configuration Snmp Configuration Asante IntraCore IC36240 Address Table Screen Asante IntraCore IC36240 Asante IntraCore IC36240 Vlan Configuration Asante IntraCore IC36240 Click Apply Igmp Configuration Asante IntraCore IC36240 Asante IntraCore IC36240 Web CLI Screen System Clock Menu Save Appendix a Basic Troubleshooting Problem Possible SolutionsEnvironmental Range Appendix B SpecificationsPhysical Characteristics PerformanceTechnical Support and Warranty Standards ComplianceAppendix C FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Appendix D Online Warranty Registration Access List IndexIgmp LED Safety Priority Queuing Vlan