Agilent Technologies 668xA, 665xA, 664xA manual System Commands, Statques NTR Statques PTR, Systerr?

Page 44

STAT:QUES NTR

STAT:QUES PTR

These commands allow you to set or read the value of the Questionable NTR (Negative-Transition) and PTR (Positive- Transistion) registers. These registers serve as polarity filters between the Questionable Enable and Questionable Event registers to cause the following actions:

•When a bit of the Questionable NTR register is set to 1, then a 1-to-0 transition of the corresponding bit of the Questionable Condition register causes that bit in the Questionable Event register to be set.

•When a bit of the Questionable PTR register is set to 1, then a 0-to-1 transition of the corresponding bit in the Questionable Condition register causes that bit in the Questionable Event register to be set.

•If the same bits in both NTR and PTR registers are set to 1, then any transition of that bit at the Questionable Condition register sets the corresponding bit in the Questionable Event register.

•If the same bits in both NTR and PTR registers are set to 0, then no transition of that bit at the Questionable Condition register can set the corresponding bit in the Questionable Event register.

Note

Setting a bit in the PTR or NTR filter can of itself generate positive or negative events in the

 

corresponding Questionable Event register.

 

 

 

 

 

Command Syntax

STATus:QUEStionable:NTRansition <NRf>

 

 

STATus:QUEStionable:PTRansition <NRf>

 

Parameters

0 to 32727

 

 

Suffix

(None)

 

 

Default Value

0

 

 

Examples

STAT:QUES:NTR 16

STATUS:QUESTIONABLE:PTR 512

 

Query Syntax

STAT:QUES:NTR?

STAT:QUES:PTR?

 

Returned Parameters

<NR1> (Register value)

 

Related Commands

STAT:QUES:ENAB

 

System Commands

SYST:ERR?

This query returns the next error number followed by its corresponding error message string from the remote programming error queue. The queue is a FIFO (first-in, first-out) buffer that stores errors as they occur. As it is read, each error is removed from the queue. When all errors have been read, the query returns 0,NO ERROR. If more errors are accumulated than the queue can hold, the last error in the queue will be -350,TOO MANY ERRORS (see Table 5-1 in "Chapter 5 - Error Messages" for other error codes).

You can use the power supply front panel key to read errors from the queue. Errors generated at the front panel are not put into the queue but appear immediately on the display.

Query Syntax

SYSTem:ERRor?

Parameters

(None)

Returned Parameters

<NRI>,<SRD>

Examples

SYST:ERR? SYSTEM:ERROR?

Related Commands

(None)

44 Language Dictionary

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Programming Guide Gpib DC Power Supplies Agilent Part No Microfiche Part No JulySafety Guidelines Printing HistoryContents Description of Subsystem Commands System CommandsCurrent Subsystem Display SubsystemCommand Summary Programming Parameters Power Supply Status Structure Operation Status GroupVoltage Subsystem Questionable Status GroupPage General Information About this GuideDocumentation Summary User’s GuidePrerequisites for Using this Guide VXIplug&play Power Product Instrument DriversDownloading and Installing the Driver Accessing Online HelpGpib Capabilities Of The Power Supply Remote ProgrammingIntroduction To Scpi ConventionsTypes of Scpi Commands Scpi MessagesStructure of a Scpi Message Voltlev 4.5PROT 4.8CURR?NLVoltlev 4.5 Prot 4.8 CURR? Parts of a Scpi MessageVolt LEV Prot Curr Traversing the Command Tree Query IndicatorMessage Unit Separator Root SpecifierEffect of Optional Headers Moving Among SubsystemsOutputprotectionclear STATUSOPERATIONCONDITION? OUTPUTPROTECTIONCLEARSTATUSOPERATIONCONDITION?Including Common Commands Scpi QueriesValue Coupling Scpi Data FormatsExamples Controlling the Output Programming Status Saving and Recalling StatesWriting to the Display System Considerations Programming the Digital I/O PortGpib Address DigdataAction Display Shows Assigning the Gpib Address In ProgramsError Handling DOS DriversAgilent Basic Controllers Sample Program CodeProgramming Some Power Supply Functions Iout = OUTPUTS2Call Ioenter PS,OEVENT SPOL%=O While C O Language Dictionary IntroductionDescription Of Common Commands Common Commands Syntax DiagramCLS ESEOPC ESR?IDN? OPC? OPT?PSC PSC 0 *PSCCommand Syntax RCL NRf Parameters Example Query Syntax None Related CommandsRCL PSC *RST *SAVSAV RSTSAV Bit Configuration of Status Byte Register SRESTB? SREWAI TRGTST? Description of Subsystem Commands Calibration CommandsAbor AborCurrprotstat Current SubsystemCurr Currtrig Display Subsystem DigdataDisp Digdata 7 DigitaldatavalueDisptext Defaultmode DispmodeDisptext Dispmode Norm Displaymode Normal Displaywindowmode TextInitiate Subsystem Measure SubsystemInit Initcont MEASCURR? MEASVOLT?Outpprotcle Outpprotdel Output SubsystemOutp Outprel OutprelpolOutprel 1 Outprel OFF Outprelpol NormStatus Subsystem StatpresStatus Operation Registers STATOPER?STATUSOPERATIONENABLE? StatoperenabStatoper NTR Statoper PTR Statoperenab 1312 StatoperenabStatus Questionable Registers STATQUES?STATQUESCOND? StatquesenabSystem Commands SYSTERR? SYSTEMERROR?Statques NTR Statques PTR SYSTERR?Trigger Subsystem SystlangSYSTVERS? TrigVoltage Subsystem TrigsourVolt Volttrig Trigsour BUS Triggersource BUSCommand Summary Command SummaryCommand Parameters Subsystem Commands VoltprotCommand Parameters Common Commands ParametersProgramming Parameters Currlevtrig MAXVoltlevtrig MAX Voltprot MAXPage Power Supply Status Structure Register CommandsStatus Reporting Operation Status GroupCAL WTGUNR OPCStatus Questionable Commands Register Query Cleared By Questionable Status GroupStandard Event Status Group STATQUESNTR?Service Request Enable Register Initial Conditions At Power OnStatus Byte Register Output QueuePON Power-On Bit Servicing an Operation Status Mode EventDefault Power On Register States Condition Caused By StatpreServicing Questionable Status Events Monitoring Both Phases of a Status TransitionAdding More Operation Events Scpi Command Completion DFI Discrete Fault IndicatorRI Remote Inhibit WAIPage Error Messages Power Supply Hardware Error MessagesCalibration Error Messages System Error MessagesSummary of System Error Messages Error Error String Description/Explanation/Examples NumberScpi Confirmed Commands1 Scpi Approved CommandsScpi Conformance Information Scpi VersionNON-SCPI Commands1 Compatibility Language Compatibility LanguageParallel Polling Volt CurrVSET? ISET? CURR? VOUT?Hold OFF VolttrigHold CurrtrigFAULT? UNMASK?SRQ OFF SRQIndex IndexOperation status group, 51 optional header Trig SOUR, 46 VOLT, 46 Volt PROT, 47 Volt Trig United States Latin America Canada Australia/New ZealandEurope Asia Pacific Japan
Related manuals
Manual 142 pages 24.05 Kb Manual 67 pages 46.05 Kb

668xA, 669xA, 667xA, 664xA, 665xA specifications

Agilent Technologies has long been a pioneer in the production of high-performance electronic test and measurement instruments, particularly in the field of power sources. Among its notable offerings are the Agilent 667xA, 669xA, 665xA, 664xA, and 668xA series of power supplies. These instruments are designed to provide stable, reliable power for a variety of applications, including electronic testing, industrial processes, and research laboratories.

The Agilent 667xA series is characterized by its programmability and advanced measurement functions. These power supplies support a wide range of output voltages and currents, allowing for flexible configurations that cater to different testing needs. The built-in measurement capabilities enable users to monitor the voltage, current, and power with high precision, which is essential for ensuring optimal performance in electronic applications.

The Agilent 669xA series stands out with its high-power outputs, making it suitable for demanding applications. These power supplies deliver high voltage and current levels, making them ideal for testing high-performance devices, such as power amplifiers and motor drives. Additionally, the 669xA series includes features such as overvoltage protection and complex output sequencing to enhance the safety and reliability of the testing process.

The Agilent 665xA and 664xA series focus on delivering high accuracy and excellent regulation. These models are particularly known for their low noise operation, which is critical for sensitive applications where precision is paramount. The integrated programming capabilities allow users to automate testing sequences, thus improving efficiency in research and development settings.

The 668xA series features advanced digital signal processing that enhances the precision and stability of the output. Users benefit from features like remote sensing and monitoring, allowing feedback adjustments that maintain output accuracy despite cable losses. Furthermore, the 668xA models can integrate seamlessly with various test environments thanks to their LAN, GPIB, and USB connectivity options.

Overall, the Agilent 667xA, 669xA, 665xA, 664xA, and 668xA power supplies provide a comprehensive range of solutions for diverse electronic testing needs. With their advanced features, superb measurement capabilities, and robust performance, these instruments empower engineers and researchers to conduct their work with confidence, precision, and efficiency.
Top Page Image Contents