SEAL 44/62 user manual Unwind brakes, Roller nip settings, Image guide storage place

Page 17

4.3 Unwind brakes

Tighten the supply brake so that it applies sufficient tension to laminate. Turning the knurled collar in a clockwise direction increases the breaking tension applied on the laminate. Turning the collar counter-clockwise decreases the tension. The best setting for the brake tension is determinate by the materials you are using and is learned through experience.

4.4 Roller nip settings

Whenever you mount onto a board, etc., it is important to adjust the rollers to create a gap nearly equal to the thickness of the board being used. This is done so that anything passing between the rollers will receive the right amount of pressure and prevent damage to the roller’s rubber surface (and possibly the board).

How to set the nip:

Determine the thickness of the board that you will use for mounting.

Adjust the nip setting. Grasp the nip-knob with your right hand and push in approximately ¼” (6mm) to the left. Once the knob has disengaged from the stop, it may be rotated forward or backward (clockwise or counter-clockwise, as viewed from the right hand side of the unit), until the desired value is opposite the window at the base of the knob. Releasing the knob so that it moves back to the right and clicks into place will set the rollers for use. The measurements on the knob correspond to the ‘Pouch board’ thickness. There is also fully closed stop for film only applications.

Note:

For non-standard substrate thickness, select the next lowest nip-setting i.e.; 7mm board – select ¼” (6mm) nip.

4.5 Image guide storage place.

When not in use, the Image Guide can be stored in the stand.

English

Figure 9

Unit description

15

Image 17
Contents 44/62 Ultra Plus English Français Deutsch Español Italiano 44/62 Ultra PlusIntroduction Table of Contents Loading the machine Application ProcessesTechnical Specifications SpecificationsElectrical specifications Emergency stop-buttons Safety / Important SafeguardsSafety symbols used on the equipment Power supply Unpacking and InstallationAmbient Conditions SurroundingsSetting up the laminator in 4 steps Page Nut Feet Unit Description Motor control Control panelPage Image guide storage place Roller nip settingsUnwind brakes Application Process Control SheetLoading the machine Application ProcessesPage Webbing the films Page Feeding images Laminating and adhesive coating Decaling Decaling without liner Mounting Encapsulating Pre-Coating Mounting using a ProSEAL Mounting Board10Mounting and Lamination using a ProSEALpouch Board Application Processes Maintenance & Cleaning Troubleshooting Glossary of Terms Limited Warranty Index

44/62 specifications

SEAL 44/62 is a notable vessel in the realm of modern naval architecture, epitomizing cutting-edge technology and design for maritime operations. Classed as a versatile multi-role vessel, the SEAL 44/62 stands out for its ability to perform a wide array of missions, including surveillance, reconnaissance, and special operations.

One of the main features of the SEAL 44/62 is its advanced hull design, which incorporates a lightweight composite material that enhances speed and maneuverability. The vessel employs a streamlined form that is optimized for hydrodynamic efficiency, allowing it to travel at high speeds while minimizing wake and radar signature. This is crucial for stealth missions where the element of surprise is paramount.

Propulsion is another key characteristic of the SEAL 44/62. Equipped with hybrid propulsion systems, it combines traditional diesel engines with electric motors. This dual capability not only provides efficient fuel consumption during extended operations but also allows for silent running, making it harder to detect by enemy forces or anti-submarine warfare technologies.

The vessel’s onboard technology features a state-of-the-art command and control system that integrates artificial intelligence to enhance situational awareness. This system allows operators to assess threats in real time and coordinate responses seamlessly. Additionally, advanced radar and communication systems ensure that the SEAL 44/62 can maintain secure and reliable contact with command centers and allied units.

In terms of versatility, the SEAL 44/62 is designed with modular capabilities that can be customized based on mission requirements. It can be outfitted with various mission payloads, including unmanned aerial vehicles (UAVs), remotely operated underwater vehicles (ROVs), and different sensor packages, facilitating missions ranging from intelligence gathering to combat support.

Furthermore, the SEAL 44/62's interior is designed for operability and comfort. The vessel accommodates a crew of skilled operators while ensuring they have access to all necessary facilities for extended deployments. The ergonomic workspace is equipped with modern technology that enhances efficiency and effectiveness.

Overall, the SEAL 44/62 represents a significant advancement in naval vessel design, showcasing a blend of speed, stealth, and versatility. Its advanced technologies and adaptable features make it a formidable asset in modern maritime operations, reflecting the evolving needs of naval warfare.