General Precautions and Installation Tips

amplifier with as much clearance as possible. This type of mounting will yield the best cool- ing due to the convection effect of the amplifier chassis.

General Precautions and Installation Tips

WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle.

Disconnect the vehicle's ground wire at the battery before making or breaking connections to the audio system's power supply terminals.

Do not use this amplifier unmounted. Failing to securely mount the amplifier can result in damage or injury, particularly in the event of an accident. An unmounted amplifier becomes a dangerous projectile in the event of a crash. Never mount the amplifier where it might get wet. Mount the amplifier so the wire connections will not be pulled. Route the wires where they will not be scraped, pinched or damaged in any fashion.

The +12V power supply wire must be fused as close as possible to the battery terminal, ide- ally within 18". Use the recommended fuse size or circuit breaker listed in the Power Connections section of this manual.

If you need to replace the fuse plugged into the side of the amplifier, replace the fuse with the same size ATC / MAXI type fuse that came with the amplifier. If you are not sure as to the correct value, refer to the Power Connections section of this manual for details. Using a high- er current fuse may result in damage to the amplifier that is not covered under warranty.

NOTE: Make sure all the equipment in the system is turned off when making or break- ing connections to the input RCA's or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections.

Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems.

Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air circulation. Remember, beach blankets, last week's laundry, school books and homework papers located on top of the amplifier do not improve air flow and may become damaged.

Tools of the Trade

Listed below are the majority of the tools required to perform an installation. Having the proper tools will make the installation that much easier. Some of these tools are necessities. Some just make the job easier.

●Allen Wrenches (2.5mm and 3mm)

●DMM or VOM

●Electric drill with assorted drill bits

●Grommets

●Heat shrink tubing

●Marking pen

●Nylon tie straps

●Phillips and flat blade screw drivers

10	©2003 Directed Electronics, Inc.

3002, 2002 specifications

Orion Car Audio is renowned for its dedication to delivering high-performance audio systems for automotive enthusiasts. Among their standout products are the Orion Car Audio 3002 and 2002 amplifiers, which are both appreciated for their excellent sound quality and robust build.

The Orion 3002 is a powerful 2-channel amplifier designed to drive high-performance speakers with ease. With an output power of 300 watts RMS, it is capable of delivering dynamic sound reproduction that can elevate any listening experience. One of its notable features is its high-and low-pass filters, which allow users to tailor the audio output to match their specific preferences and vehicle acoustics. Additionally, the Orion 3002 comes equipped with a variable gain control, enabling users to adjust the input sensitivity to maximize sound fidelity without distortion.

In contrast, the Orion 2002, while slightly less powerful at 200 watts RMS, shares many of the same technologies that make the 3002 a favorite among car audio enthusiasts. Its compact design makes it easy to install in a variety of vehicle types, ensuring that quality sound is accessible to all. The 2002 also includes a temperature protection circuit to prevent overheating, which extends the life of the amplifier and ensures consistent performance even during prolonged use.

Both models are built with durability in mind, featuring rugged aluminum extruded heatsinks that dissipate heat efficiently and maintain optimal performance. This durability is paired with a sleek aesthetic that complements modern vehicle interiors.

Another significant characteristic of both the Orion 3002 and 2002 is their compatibility with a range of subwoofers. This flexibility allows users to create their own tailored sound systems suited to their individual preferences. Additionally, the amplifiers feature low-frequency response capabilities that enhance bass performance, delivering rich and powerful low-end sound that is essential for a complete audio experience.

Overall, the Orion Car Audio 3002 and 2002 are exemplary choices for those seeking to upgrade their car audio systems. With their powerful output, advanced technologies, and durable construction, they provide users with a high-fidelity audio experience that can satisfy even the most discerning audiophiles. Whether you are cruising down the highway or parked at a tailgate, these amplifiers are designed to deliver a soundtrack that brings life to any journey.