Step By Step Installation

●Pliers (standard and needle nose)

●Reference CD with 1 kHz Sine Wave at 0dB level (all bits high)

●RTA (real time analyzer)

●Soldering iron and solder

●Utility knife

●Wire brush or sandpaper for chassis grounding

●Wire crimper

●Wire cutters

●Wire strippers

Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information.

Step 2 Decide on the system configuration for your amplifier. For system sugges- tions, refer to the Speaker Connections section of this guide.

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great potential for induced system noise.

Step 4 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding them- selves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 5 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

Step 7 Disconnect the vehicle's battery ground terminal.

Step 8 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this manual for correct wiring instructions.

Step 9 Connect power wires to the amplifier. At this time do not connect the fuse at the main battery.

Step 10 Reconnect the ground terminal to the battery.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System sec- tion of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in voiding of your warranty and possible damage to the amplifier.

3002, 2002 specifications

Orion Car Audio is renowned for its dedication to delivering high-performance audio systems for automotive enthusiasts. Among their standout products are the Orion Car Audio 3002 and 2002 amplifiers, which are both appreciated for their excellent sound quality and robust build.

The Orion 3002 is a powerful 2-channel amplifier designed to drive high-performance speakers with ease. With an output power of 300 watts RMS, it is capable of delivering dynamic sound reproduction that can elevate any listening experience. One of its notable features is its high-and low-pass filters, which allow users to tailor the audio output to match their specific preferences and vehicle acoustics. Additionally, the Orion 3002 comes equipped with a variable gain control, enabling users to adjust the input sensitivity to maximize sound fidelity without distortion.

In contrast, the Orion 2002, while slightly less powerful at 200 watts RMS, shares many of the same technologies that make the 3002 a favorite among car audio enthusiasts. Its compact design makes it easy to install in a variety of vehicle types, ensuring that quality sound is accessible to all. The 2002 also includes a temperature protection circuit to prevent overheating, which extends the life of the amplifier and ensures consistent performance even during prolonged use.

Both models are built with durability in mind, featuring rugged aluminum extruded heatsinks that dissipate heat efficiently and maintain optimal performance. This durability is paired with a sleek aesthetic that complements modern vehicle interiors.

Another significant characteristic of both the Orion 3002 and 2002 is their compatibility with a range of subwoofers. This flexibility allows users to create their own tailored sound systems suited to their individual preferences. Additionally, the amplifiers feature low-frequency response capabilities that enhance bass performance, delivering rich and powerful low-end sound that is essential for a complete audio experience.

Overall, the Orion Car Audio 3002 and 2002 are exemplary choices for those seeking to upgrade their car audio systems. With their powerful output, advanced technologies, and durable construction, they provide users with a high-fidelity audio experience that can satisfy even the most discerning audiophiles. Whether you are cruising down the highway or parked at a tailgate, these amplifiers are designed to deliver a soundtrack that brings life to any journey.