Lifebreath 155MAX, 200MAX, 95MAX installation manual Symptom Cause Solution, Occupant

Page 29

SYMPTOM

CAUSE

SOLUTION

Poor Air Flows

• 1/4” (6 mm) mesh on the outside hoods is plugged

• clean exterior hoods or vents

 

• filters plugged

• remove and clean filter

 

• core obstructed

• remove and clean core

 

• house grilles closed or blocked

• check and open grilles

 

• dampers are closed if installed

• open and adjust dampers

 

• poor power supply at site

• have electrician check supply voltage at house

 

• ductwork is restricting HRV/ERV

check duct installation

 

• improper speed control setting

• increase the speed of the HRV/ERV

 

• HRV/ERV airflow improperly balanced

• have contractor balance HRV/ERV

 

 

 

Supply air feels cold

• poor location of supply grilles, the airflow may irritate

• locate the grilles high on the walls or under the baseboards,

 

the occupant

install ceiling mounted diffuser or grilles so as not to directly

 

 

spill the supply air on the occupant (eg. over a sofa)

 

• outdoor temperature extremely cold

• turn down the HRV/ERV supply speed. A small duct heater

 

 

(1kw) could be used to temper the supply air

 

 

• placement of furniture or closed doors is restricting the

 

 

movement of air in the home

 

 

• if supply air is ducted into furnace return, the furnace fan

 

 

may need to run continuously to distribute ventilation

 

 

air comfortably

 

 

 

Dehumidistat is not Operating

• improper low voltage connection

• check that the correct terminals have been used

 

• external low voltage is shortened out by a staple or nail

• check external wiring for a short

 

• check dehumidistat setting it may be on OFF

• set the dehumidistat at the desired setting

 

 

 

Humidity Levels are too High

• dehumidistat is set too high

• set dehumidistat lower

Condensation is appearing on the windows

• HRV/ERV is undersized to handle a hot tub, indoor pool, etc.

• cover pools, hot tubs when they are not in use

 

• lifestyle of the occupants

• avoid hanging clothes to dry, storing wood and venting clothes

 

 

dryer inside. Heating wood may have to be moved outside

 

• moisture coming into the home from an unvented or

• vent crawl space and place a vapour barrier on the floor

 

unheated crawl space

of the crawl space

 

• moisture is remaining in the washroom and kitchen areas

• ducts from the washroom should be sized to remove moist

 

 

air as effectively as possible, use of a bathroom fan for

 

 

short periods will remove additional moisture

 

• condensation seems to form in the spring and fall

• on humid days, as the seasons change, some condensation

 

 

may appear but the homes air quality will remain high with

 

 

some HRV/ERV use

 

• HRV/ERV is set at too low a speed

• increase speed of the HRV/ERV

 

 

 

Humidity Levels are too Low

• dehumidistat control set too low

• set dehumidistat higher

 

• blower speed of HRV/ERV is too high

• decrease HRV/ERV blower speed

 

• lifestyle of occupants

• humidity may have to be added through the use of humidifiers

 

• HRV/ERV air flows may be improperly balanced

• have a contractor balance HRV/ERV airflows

 

 

 

HRV/ERV and / or Ducts Frosting up

 

• Note: minimal frost build-up is expected on cores before

 

 

unit initiates defrost cycle functions

 

• HRV/ERV air flows are improperly balanced

• have HVAC contractor balance the HRV/ERV

 

• malfunction of the HRV/ERV defrost system

• using the self-test feature at the Base Module, press the fan

 

 

control symbol, the damper defrost unit should cycle its full

 

 

travel when working properly.

 

 

 

Condensation or Ice Build Up in Insulated Duct to

• incomplete vapour barrier around insulated duct

• tape and seal all joints

the Outside

• a hole or tear in outer duct covering

• tape any holes or tears made in the outer duct covering

 

 

• ensure that the vapour barrier is completely sealed

 

 

 

Water in the bottom of the HRV/ERV

• drain pans plugged

• ensure O-Ring on drain nozzle sits properly

 

• improper connection of HRV/ERVs drain lines

• look for kinks in line

 

• HRV/ERV is not level

• check water drain connections

 

• drain lines are obstructed

• make sure water drains properly from pan

 

• HRV/ERV heat exchange core is not properly installed

 

29

Image 29
Contents 200ERVD Contains95MAX Table of Contents ERV Questions & Answers Page Engineering Data Model 95MAXModel 155MAX Dimensions 155MAX inches mmModel 200MAX Dimensions 200MAX inches mmModel Maxtop Dimensions Maxtop inches mmModel 195DCS Dimensions 195DCSThermally CONDUCTIVE, Patented Aluminum Core Model 300DCSModel 200ERV Dimensions 200ERV inches mmModel 200ERVD Dimensions 200ERVDFunction & Control To select mode of operation for ControlAir NEW! AIR Sentry AIR Quality Sensor Optional Remote ControlsUsing the Dehumidistat MAX Port Specifications Location InstallationInstalling AIR Ducts Dampers and Grilles Supply AIR DuctingInstallation Diagrams Simplified Installation Supply/Return Method Fully Dedicated System Pitot Tube AIR Flow Balancing Balancing Collar Instructions Inspect Exterior Hoods at least once a month Maintenance Routine for ERV for HRV, see previous Occupant Symptom Cause SolutionTechnical Bulletin Residential Wiring Diagram McCormick Blvd. London, Ontario N5W 4C
Related manuals
Manual 32 pages 16.73 Kb Manual 12 pages 19.73 Kb

155MAX, 95MAX, 200MAX specifications

Lifebreath is well-known for its innovative heat recovery ventilators that enhance indoor air quality while conserving energy. Among their acclaimed models, the Lifebreath 150SP, 200MAX, 150MAX, and 200STD stand out for both their functionality and design, delivering optimal performance for various residential and commercial applications.

The Lifebreath 150SP is designed for spaces requiring effective air exchange while maintaining energy efficiency. This model boasts a compact design, making it ideal for smaller homes or apartments. One of its main features includes a top-mounted control panel with a user-friendly interface, allowing for easy adjustment of settings. Equipped with a high-efficiency heat exchanger, the 150SP effectively transfers heat from the outgoing stale air to the incoming fresh air, minimizing energy loss. Additionally, the unit operates quietly, ensuring that comfort is not compromised.

On to the 200MAX, this model is engineered for larger spaces. With increased airflow capacity, it ensures consistent air quality in bigger areas while optimizing energy consumption. The 200MAX features advanced filtering systems that capture dust, pollen, and other allergens, promoting a healthier indoor environment. Its built-in defrosting system operates automatically, enhancing efficiency during colder months. The 200MAX also supports optional accessories, such as a programmable timer and an energy recovery ventilator, allowing users to customize performance to meet specific needs.

The Lifebreath 150MAX pairs the efficiency of the 150SP with added versatility. This model is suitable for mid-sized spaces and comes equipped with a dual motor system. This unique feature provides users with the flexibility to adjust airflow independently, accommodating varying room conditions. The 150MAX excels in both heating and cooling modes, ensuring comfort year-round.

Finally, the Lifebreath 200STD offers a straightforward approach to ventilation without compromising on performance. Designed for standard residential applications, the 200STD is easy to install and maintain, featuring a washable pre-filter. This model is energy efficient and operates quietly while delivering excellent air exchange rates, making it perfect for families seeking reliable indoor air management.

In conclusion, the Lifebreath range—150SP, 200MAX, 150MAX, and 200STD—showcases superior design and cutting-edge technology. With their focus on energy efficiency, user comfort, and adaptable features, Lifebreath models uphold a promise of high indoor air quality and sustainable living. These systems not only contribute to a healthier environment but also reduce energy costs, making them an ideal investment for any modern building.