Toshiba TLPX10E owner manual How to use the output connector

Page 27

How to use the output connector

You can output video and audio signals to a computer monitor, a stereo system, etc.

Check that the power for the projector and the equipments is off before connecting the cables.

Computer monitor, etc.

CONTROL USB	MONITOR OUT		COMPUTER IN 1		COMPUTER IN 2
			( Y/PB/PR )
	AUDIO	AUDIO		VIDEO IN
	OUT	IN	R - AUDIO - L		VIDEO S-VIDEO

CONTENTS

27

Installation and connection

IN 2

			COMPUTER
		IN 1
		R )
	B/P
OUT
MONITOR
USB
CONTROL
		IN	S-	VIDEO
		IN	S-
		VIDEOVIDEO
		- L
	R -	AUDIO
	R -
	AUDIO
AUDIO	IN
AUDIO
OUT

To AUDIO OUT jack

To MONITOR OUT connector Be sure to connect in the proper direction.

Audio cable (not supplied)

Stereo system, etc.

Pin plug (red)

To audio input (R)

Pin plug (white)

To audio input (L)

Notes

•The audio signals of the input source selected by the input select operation are output from the AUDIO OUT jack. The signal level (volume) is fixed.

•The analog RGB signals of the COMPUTER IN 1 or COMPUTER IN 2 connector selected by the input select operation are output from the MONITOR OUT connector. If neither of these input sources is selected, the analog RGB signal of the COMPUTER IN 1 connector is output. (Digital RGB signals are not output.)

•Signals are output from the MONITOR OUT connector even when in the standby mode.

•Do not turn the projector on or off with the stereo system, etc., turned on. This may damage the stereo’s speakers.

Image 27

Contents TLP-X10E Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Power Sources Source of LightVentilation Important Safety Instructions Stack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Important Safety InstructionsDamage Requiring Service Replacement PartsStrong light may cause damage to your eyes or sight Safety CheckDo not carry by the camera arm Do not move the projector while the arm is still erectPower supply cord selection Contents Use Names of each part on the main unitVOL/ADJ buttons 30 41 48 Use Control connector RS-232C Connector 26 USB connectorLaser emission part Names of each part on the remote controlAttach the cover Install the batteriesLoading batteries Open the coverAbout Remote control operationFloor-mounted projector placement Side view Determine the screen size projected on the screenConnect the power cord Take off the lens coverInsert the other end in a wall outlet Turn clockwise to lift up Turn counterclockwise to lower Projector placement angle adjustmentInstallation and connection Ceiling-mounted projector placementConnecting a computer Computer in 2 Connector DVI connector Connecting a computer with DVI output connectorConnecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Turn on the connected equipment and put it Playback modeProjection on the screen Press ON/STANDBYSelect the input source Signal sent from the computerZooming lever Adjust the picture size by turningFocusing ring Press VOL/ADJ +/ to adjust volumeTurning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Press Auto SET Adjusting the picture automaticallyPress Auto Keystone Correcting the keystone distortionOperations Remote controlCutting off the picture and sound temporarily Press MutePicture freezes Icon Appears in the freeze modeFreezing the picture Press FreezeIcon Appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Pressed again Displaying InformationPress Call Information described below is displayedOperating a computer by the remote control About memory cards Projecting images stored in a memory cardPress Input repeatedly to select the memory card input Insert the memory card into the card slotChanging Remote control Control panelDescription of screen Use VOL/ADJ +/ to change pages.Press ENTER. Slide display Press VOL/ADJ +/-. Slide transitionPress Exit To eject the memory card Projecting images stored in a memory cardQuick Menu Adjustments and settings on the menu screenAdjustments and settings on the menu screen Start Operating the menu screenQuick Menu adjustments and settings Press MenuQuick Menu appears See the table below Types of adjustment and setting items are differentAuto. demo Memory card input Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Lamp powerPress Exit to return to the Quick Menu Sub-menu screen of input source setting appearsPress Enter Press VOL/ADJ +/- to select the type of input sourceUse the selection buttons / to select a language Sub-menu screen of interval setting appears Use the selection buttons / to select interval timeMenu screen disappears Full Menu adjustments and settings -Picture AdjustmentsPress Menu twice Full Menu adjustments and settings Picture Slide show Memory card input Picture mode RGB inputInput select mode Memory card input Screen sizeSub-menu of selected items appears PositionLevel Press Exit to return to the Full MenuSub-menu of selected items appears Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Video mode Video input, S-video inputFull Menu adjustments and settings Picture Full Menu settings Audio Loudness After the settings are finished, press ExitSpeaker output Channel selectFull Menu settings Keystone Use the selection buttons To select Setting itemsUse the selection buttons To display Keystone menu Disappears After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter Press Exit several times until the menu screenUse the selection buttons To display Display menu Full Menu settings DisplayUse the selection buttons To select Setting items Settings When pressed once, the Quick Menu screen appears. WhenWhen selecting Language in step Start-up screen No signal background Setting of screen of no signal inputMenu position Menu background translucentFull Menu settings Default setting Use the selection buttons To display Default setting menuWhen pressed once, the Quick Menu screen appears. When Control panel Main unit side Sub-menu of Input source setting appearsUse the selection buttons / to select the projection mode Sub-menu of Projection mode appearsRear ceiling Ceiling-mounted rear projection No signal power off Power onPress VOL/ADJ +/ to set Full Menu settings Factory reset mode Factory default settingPicture menus for the each input to Full Menu settings Factory reset mode Menu screen disappears PIP menu settingSize Set the PIP sub-picture size Audio Set the audio input sourcePart names of the document imaging camera model Preparation of the document imaging camera Light turns on Press ARM LightSet a document to be projected Camera control panelMove the camera head to adjust the size Picture Press Camera to select the camera input modeCamera in reverse Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Follow the steps of Preparation of the document imagingScreen Balance Press W.BALANCE to turn the Lock indicatorLock the white balance Project a white paper and enlarge it to fillPaper or cloth Correcting illuminated defectsWith the document camera operating, fully Cover the camera lens with a piece of blackStore the camera images into the memory card Trouble indications IndicatorPower does not come on Power turns off or does not come onTake off the air filter cover Air filter cleaningUnplug the power cord Clean the air filterMount the air filter cover Air filter cleaningInstall it Assemble the air filterReplacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitHandle to pull out the lamp Lamp replacementPull out the lamp Loosen two screws, and pull off the lamp coverSlide the cover in place and tighten two screws Reset the lamp timerLoad a new lamp Attach the lamp coverSymptom Cause Correction Before calling service personalBefore calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable RGB signal Applicable signalCompatible video signal Applicable signalSignal assignment of RS-232C Interface format Controlling the projector by using RS-232CControlling the projector by using RS-232C AS1 MB1 VLU Auto SET Specifications Mini DIN 8-pin RS-232CUSB output Type B Replacement lamp Specifications