Toshiba TLPX10E owner manual Important Safety Instructions, Damage Requiring Service, Servicing

Page 7

IMPORTANT SAFETY INSTRUCTIONS (continued)

CONTENTS

7

16.If glass components, including lens and lamp, should break, contact your dealer for repair service.

This product incorporates glass components, including a lens and a lamp. If such parts should break, please handle with care to avoid injury and contact your dealer for repair service. The broken pieces of glass may cause to injury.

In the unlikely event of the lamp rupturing, thoroughly clean the area around the projector and discard any edible items placed in that area.

17.Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the power-supply cord or plug is damaged.

b)If liquid has been spilled, or objects have fallen into the product.

c)If the product has been exposed to rain or water.

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e)If the product has been dropped or damaged in any way.

f)When the product exhibits a distinct change in performance – this indicates a need for service.

18.Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. (Replacement of the lamp only should be made by users.)

Before use

Continued

Image 7
Contents TLP-X10E Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Source of Light Power SourcesVentilation Important Safety Instructions Stack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Important Safety InstructionsDamage Requiring Service Replacement PartsStrong light may cause damage to your eyes or sight Safety CheckDo not carry by the camera arm Do not move the projector while the arm is still erectPower supply cord selection Contents Use Names of each part on the main unitVOL/ADJ buttons 30 41 48 Use Control connector RS-232C Connector 26 USB connectorLaser emission part Names of each part on the remote controlAttach the cover Install the batteriesLoading batteries Open the coverAbout Remote control operationFloor-mounted projector placement Side view Determine the screen size projected on the screenTake off the lens cover Connect the power cordInsert the other end in a wall outlet Turn clockwise to lift up Turn counterclockwise to lower Projector placement angle adjustmentInstallation and connection Ceiling-mounted projector placementConnecting a computer Computer in 2 Connector DVI connector Connecting a computer with DVI output connectorConnecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Turn on the connected equipment and put it Playback modeProjection on the screen Press ON/STANDBYSelect the input source Signal sent from the computerZooming lever Adjust the picture size by turningFocusing ring Press VOL/ADJ +/ to adjust volumePress ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Press Auto SET Adjusting the picture automaticallyPress Auto Keystone Correcting the keystone distortionOperations Remote controlCutting off the picture and sound temporarily Press MutePicture freezes Icon Appears in the freeze modeFreezing the picture Press FreezeEnlarging the picture size Icon Appears in the resize modePress Resize Press PIP Displaying PIP Sub-picturesSub-picture is displayed Pressed again Displaying InformationPress Call Information described below is displayedOperating a computer by the remote control About memory cards Projecting images stored in a memory cardPress Input repeatedly to select the memory card input Insert the memory card into the card slotChanging Remote control Control panelDescription of screen Use VOL/ADJ +/ to change pages.Press VOL/ADJ +/-. Slide transition Press ENTER. Slide displayPress Exit To eject the memory card Projecting images stored in a memory cardQuick Menu Adjustments and settings on the menu screenAdjustments and settings on the menu screen Start Operating the menu screenPress Menu Quick Menu adjustments and settingsQuick Menu appears See the table below Types of adjustment and setting items are differentAuto. demo Memory card input Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Lamp powerPress Exit to return to the Quick Menu Sub-menu screen of input source setting appearsPress Enter Press VOL/ADJ +/- to select the type of input sourceUse the selection buttons / to select a language Use the selection buttons / to select interval time Sub-menu screen of interval setting appearsMenu screen disappears Adjustments Full Menu adjustments and settings -PicturePress Menu twice Full Menu adjustments and settings Picture Slide show Memory card input Picture mode RGB inputInput select mode Memory card input Screen sizeSub-menu of selected items appears PositionLevel Press Exit to return to the Full MenuSub-menu of selected items appears Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Video mode Video input, S-video inputFull Menu adjustments and settings Picture Full Menu settings Audio Loudness After the settings are finished, press ExitSpeaker output Channel selectUse the selection buttons To select Setting items Full Menu settings KeystoneUse the selection buttons To display Keystone menu Disappears After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter Press Exit several times until the menu screenUse the selection buttons To display Display menu Full Menu settings DisplayUse the selection buttons To select Setting items Settings When pressed once, the Quick Menu screen appears. WhenWhen selecting Language in step Start-up screen No signal background Setting of screen of no signal inputMenu position Menu background translucentUse the selection buttons To display Default setting menu Full Menu settings Default settingWhen pressed once, the Quick Menu screen appears. When Control panel Main unit side Sub-menu of Input source setting appearsSub-menu of Projection mode appears Use the selection buttons / to select the projection modeRear ceiling Ceiling-mounted rear projection Power on No signal power offPress VOL/ADJ +/ to set Factory default setting Full Menu settings Factory reset modePicture menus for the each input to Full Menu settings Factory reset mode Menu screen disappears PIP menu settingSize Set the PIP sub-picture size Audio Set the audio input sourcePart names of the document imaging camera model Preparation of the document imaging camera Light turns on Press ARM LightSet a document to be projected Camera control panelMove the camera head to adjust the size Picture Press Camera to select the camera input modeCamera in reverse Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Follow the steps of Preparation of the document imagingScreen Balance Press W.BALANCE to turn the Lock indicatorLock the white balance Project a white paper and enlarge it to fillPaper or cloth Correcting illuminated defectsWith the document camera operating, fully Cover the camera lens with a piece of blackStore the camera images into the memory card Trouble indications IndicatorPower does not come on Power turns off or does not come onTake off the air filter cover Air filter cleaningUnplug the power cord Clean the air filterMount the air filter cover Air filter cleaningInstall it Assemble the air filterReplacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitHandle to pull out the lamp Lamp replacementPull out the lamp Loosen two screws, and pull off the lamp coverSlide the cover in place and tighten two screws Reset the lamp timerLoad a new lamp Attach the lamp coverSymptom Cause Correction Before calling service personalBefore calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable RGB signal Applicable signalCompatible video signal Applicable signalSignal assignment of RS-232C Interface format Controlling the projector by using RS-232CControlling the projector by using RS-232C AS1 MB1 VLU Auto SET Mini DIN 8-pin RS-232C SpecificationsUSB output Type B Replacement lamp Specifications