Toshiba TLPX10E owner manual Load a new lamp, Attach the lamp cover, Reset the lamp timer

Page 87

Lamp replacement (continued)

CONTENTS

87

Notes

•When the CALL button is pressed, the “Lamp

time” (the approximate amount of time the lamp has been used) is displayed. 38

•The lamp should be replaced if the total working time exceeds about 1,000 hours.

When the “Lamp time” is displayed 1000 hours,

the icon and a message appear. They will disappear when you do some operation.

•Attach the lamp cover firmly after replacing the lamp. If it is not set correctly, the power will not turn on.

•Use a new lamp when replacing it.

•The lamp is made of glass and is very fragile. Do not touch the lamp with your bare hands and do not jolt or damage it. Do not use an exhausted lamp.

•Dispose the exhausted lamp as toxic wastes.

5

6

Load a new lamp.

Slide until it hits the bottom and tighten the two fixed screws.

Attach the lamp cover.

Slide the cover in place and tighten two screws.

3

2 1

Maintenance

7

Reset the lamp timer.

 

 

Refer to the lamp instructions for resetting.

Page 86 Page 88
Image 87
Page 86 Page 88
Contents TLP-X10E Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Power Sources Source of LightVentilation Important Safety Instructions Stack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Important Safety InstructionsDamage Requiring Service Replacement PartsStrong light may cause damage to your eyes or sight Safety CheckDo not carry by the camera arm Do not move the projector while the arm is still erectPower supply cord selection Contents Use Names of each part on the main unitVOL/ADJ buttons 30 41 48 Use Control connector RS-232C Connector 26 USB connectorLaser emission part Names of each part on the remote controlAttach the cover Install the batteriesLoading batteries Open the coverAbout Remote control operationFloor-mounted projector placement Side view Determine the screen size projected on the screenConnect the power cord Take off the lens coverInsert the other end in a wall outlet Turn clockwise to lift up Turn counterclockwise to lower Projector placement angle adjustmentInstallation and connection Ceiling-mounted projector placementConnecting a computer Computer in 2 Connector DVI connector Connecting a computer with DVI output connectorConnecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Turn on the connected equipment and put it Playback modeProjection on the screen Press ON/STANDBYSelect the input source Signal sent from the computerZooming lever Adjust the picture size by turningFocusing ring Press VOL/ADJ +/ to adjust volumeTurning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Press Auto SET Adjusting the picture automaticallyPress Auto Keystone Correcting the keystone distortionOperations Remote controlCutting off the picture and sound temporarily Press MutePicture freezes Icon Appears in the freeze modeFreezing the picture Press FreezeIcon Appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Pressed again Displaying InformationPress Call Information described below is displayedOperating a computer by the remote control About memory cards Projecting images stored in a memory cardPress Input repeatedly to select the memory card input Insert the memory card into the card slotChanging Remote control Control panelDescription of screen Use VOL/ADJ +/ to change pages.Press ENTER. Slide display Press VOL/ADJ +/-. Slide transitionPress Exit To eject the memory card Projecting images stored in a memory cardQuick Menu Adjustments and settings on the menu screenAdjustments and settings on the menu screen Start Operating the menu screenQuick Menu adjustments and settings Press MenuQuick Menu appears See the table below Types of adjustment and setting items are differentAuto. demo Memory card input Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Lamp powerPress Exit to return to the Quick Menu Sub-menu screen of input source setting appearsPress Enter Press VOL/ADJ +/- to select the type of input sourceUse the selection buttons / to select a language Sub-menu screen of interval setting appears Use the selection buttons / to select interval timeMenu screen disappears Full Menu adjustments and settings -Picture AdjustmentsPress Menu twice Full Menu adjustments and settings Picture Slide show Memory card input Picture mode RGB inputInput select mode Memory card input Screen sizeSub-menu of selected items appears PositionLevel Press Exit to return to the Full MenuSub-menu of selected items appears Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Video mode Video input, S-video inputFull Menu adjustments and settings Picture Full Menu settings Audio Loudness After the settings are finished, press ExitSpeaker output Channel selectFull Menu settings Keystone Use the selection buttons To select Setting itemsUse the selection buttons To display Keystone menu Disappears After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter Press Exit several times until the menu screenUse the selection buttons To display Display menu Full Menu settings DisplayUse the selection buttons To select Setting items Settings When pressed once, the Quick Menu screen appears. WhenWhen selecting Language in step Start-up screen No signal background Setting of screen of no signal inputMenu position Menu background translucentFull Menu settings Default setting Use the selection buttons To display Default setting menuWhen pressed once, the Quick Menu screen appears. When Control panel Main unit side Sub-menu of Input source setting appearsUse the selection buttons / to select the projection mode Sub-menu of Projection mode appearsRear ceiling Ceiling-mounted rear projection No signal power off Power onPress VOL/ADJ +/ to set Full Menu settings Factory reset mode Factory default settingPicture menus for the each input to Full Menu settings Factory reset mode Menu screen disappears PIP menu settingSize Set the PIP sub-picture size Audio Set the audio input sourcePart names of the document imaging camera model Preparation of the document imaging camera Light turns on Press ARM LightSet a document to be projected Camera control panelMove the camera head to adjust the size Picture Press Camera to select the camera input modeCamera in reverse Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Follow the steps of Preparation of the document imagingScreen Balance Press W.BALANCE to turn the Lock indicatorLock the white balance Project a white paper and enlarge it to fillPaper or cloth Correcting illuminated defectsWith the document camera operating, fully Cover the camera lens with a piece of blackStore the camera images into the memory card Trouble indications IndicatorPower does not come on Power turns off or does not come onTake off the air filter cover Air filter cleaningUnplug the power cord Clean the air filterMount the air filter cover Air filter cleaningInstall it Assemble the air filterReplacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitHandle to pull out the lamp Lamp replacementPull out the lamp Loosen two screws, and pull off the lamp coverSlide the cover in place and tighten two screws Reset the lamp timerLoad a new lamp Attach the lamp coverSymptom Cause Correction Before calling service personalBefore calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable RGB signal Applicable signalCompatible video signal Applicable signalSignal assignment of RS-232C Interface format Controlling the projector by using RS-232CControlling the projector by using RS-232C AS1 MB1 VLU Auto SET Specifications Mini DIN 8-pin RS-232CUSB output Type B Replacement lamp Specifications
Top Page Image Contents