Toshiba TDP-T40 (XGA) Connecting a computer, Placement Styles, Operating a computer

Page 11

Operating a computer using the remote control

A computer can be operated using the projector’s remote control. This function is available on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XP OS, that is equipped with a USB port supporting the USB 1.1 (The mouse remote control is supported on OS 9 or OS X for the Macintosh).

The operation cannot be guaranteed for all the environments of computers.

1Connecting a computer

Connect the supplied Mouse remote control receiver to the computer.

Placement

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the Projection mode in the default setting menu p.33 , in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

To USB port

Mouse remote control receiver

The remote control may fail to operate if the mouse remote control receiver is exposed to bright sunlight or fluorescent lighting.

In such a case, change position or direction of the mouse remote control receiver and retry.

Ceiling-mounted front projection

 

Ceiling-mounted rear projection

 

Preparations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2Operating a computer

The mouse remote control function is available when the remote control is set to [PC Mode]. (See “Switching operation modes” .)

Point the Mouse remote control at the mouse remote control receiver, and operate the remote control’s buttons.

Moving the mouse pointer

Move the pointer control button in the direction that you wish the mouse pointer to move, then press.

To left click

Press the L-CLICK button.

To right click

Press the R-CLICK button.

To drag and drop

Move the pointer control button in a (L-)clicked state, then when the pointer is over the desired location, release the button.

Using the computer’s up and down arrow key functions Press the and buttons to switch PowerPoint® slides.

Remote Control Front

Remote Control Rear

Pointer control

L-CLICK

ENTER

R-CLICK

RETURN

WARNING

Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury.

If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident.

If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact.

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment.)

Screen As seen from above

a (min length) =

projection size (inches) – 1.1975

 

 

28.263

 

 

 

 

 

90°

a (max length) =

projection size (inches) – 1.0446

 

 

23.486

 

 

 

 

 

 

projection

projection distance a (m)

height (H)

 

min length

max length

As seen from the side

size (inches)

(cm)

(zooming max)

(zooming min)

Lens center

29.2

1.20

5.5

35.1

1.20

1.45

6.6

 

40

1.37

1.66

7.3

H

60

2.08

2.51

11.0

80

2.79

3.36

14.6

 

R-CLICK

ESC

 

 

90°

 

 

 

 

 

 

 

 

 

 

100

3.50

4.21

18.3

 

 

 

 

a

 

 

150

5.26

6.34

27.4

 

 

 

a is the distance (m) between the lens and the

200

7.03

8.47

36.6

screen, and corresponds to a range of 1.20 m to

250

8.80

10.60

45.7

11.00 m. H is the height from the image bottom to the

300

10.57

54.9

center of the lens.

 

 

 

 

20

21

Image 11
Contents TDP-T40 XGA Others Maintenance Operations Preparations Before UsingTested To Comply With FCC Standards Safety PrecautionsBefore Using USA onlyImportant Safety Instructions Important Safety Instructions Save Original Packing Materials Power Supply Cord SelectionImportant Precautions Place and Manner of InstallationOther Cautions and Informations Remote Control BatteriesExemption Clauses Contents Names of each part on the main unit Checking the package contentsControl panel Remote Control FrontRearComponent video signal Y/PB/PR from video Parts on the rear panelDry-cell batteries Preparing and using the remote controlRemote control Operating a computer PlacementConnecting a computer Placement StylesOperations Turning the power on and offConnection Basic operations Turning the power on and offBasic operations Using handy featuresFreezing the image Freeze Using handy featuresCutting off the picture and sound temporarily Mute Image adjustment menu Using the menusHow to use the menus Default setting menu Using the menuDisplay setting menu About lamp Lamp replacementMaintenance When the lamp is brokenLamp replacement Lens and main unit cleaningOthers Before calling service personnelTrouble indications Specification SpecificationsList of general specifications List of supported signals RGB signalsSeparately Sold Product SpecificationsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signals