Toshiba TDP-T420 owner manual Basic operations

Page 14

Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning the power onp.24 .

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, the start menu for language (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)

1Use the , , or button to select the desired language and press the button.

Notes

When [Auto input search] is set to [Off] in the Default setting 1 menu p.41 (factory setting is [On]), the Input select menu appears if you press the INPUT button p.41 .

If no signal is being output from the connected equipment, pressing the INPUT button does not change the input and “There is no other input signal.” will appear.

5Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot adjuster.

1 Lift up the front of the projector to the desired angle, then press the foot

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Polish

Norwegian

Finnish

Czech

Hungarian

Greek

Danish

Dutch

Rumanian

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

Indonesian

adjuster release button.

The foot adjuster extends. Release the button to lock the position.

2To fine adjust the angle, twist the foot

adjuster.

3 To adjust the horizontal angle, use the right and left tilt adjusters.

Message for setup confirmation is displayed in a selected language.

Then, the menu for lamp power selection and configuration is displayed. It is automatically set as Standard. To change the setting, follow the step 2 .

2Use the or button to select the lamp power and press the button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

Notes

When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting 2 menu p.42 , the start menu will be displayed the next time when the power is turned on.

The language can also be set via the Display setting menu p.38 and Lamp power via the Default setting 2 menu p.42 .

This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals.

To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector.

Note

When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone distortion will automatically be corrected based on the projector placement angle. If you do not desire the automatic keystone correction, set [Auto keystone] to [Off].

6Adjusting the screen size and focus

1 Use the zooming lever to adjust the

Zooming lever

Focusing ring

screen size.

 

 

 

 

2 Use the focusing ring to adjust the focus.

7 Adjusting the volume with the buttons

The speaker volume can be adjusted when an audio signal is being input.

Operations

26

27

Image 14
Contents TDP-T420 TDP-T360 Safety Precautions USA onlyImportant Safety Instructions Important Safety Instructions Place and Manner of Installation Power Supply InformationImportant Precautions Moisture CondensationOther Information Remote Control BatteriesExemption Clauses Contents Checking the package contents Names of each part on the main unitNames of each part on the control panel and remote control Label location Loading dry-cell batteries into the remote control  Operating the remote ControlOperating a computer using the remote control PlacementConnection Before connection Turning the power off Press the ON/STANDBY button Turning the power on and off Turning the power on Turn on the main power switch Turn off the main power switch Replace the lens capBasic operations Basic operations Using handy featuresUsing auto setting For computer input only Correcting the keystone distortion Resizing image Using handy features Zooming out the images  Cutting off the picture and sound temporarily Mute  Changing picture mode Setting the password How to change password  Changing screen size Setup using the Setting display Using the menusHow to set password from Off to On How to operate when password is On The position adjustment menu Using the menus The image adjustment menu  The display setting menu Default setting menu Lamp power Detailed description Fan modeRemote control code setting for remote control  Displaying Information Status displayUnplug power cord Wait until lamp is sufficiently cooled Lamp replacement When the lamp is broken About lampLamp replacement  Main unit cleaning Lens and main unit cleaning Lens cleaning Trouble indicationsTroubleshooting  List of supported signals RGB signals Specifications List of general specifications Specification List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Pin assignment of Computer 2 in & Monitor terminals Pin assignment  Main Commands Control terminal  Interface format