Toshiba TDP-T420  Displaying Information Status display, Detailed description Fan mode, Key lock

Page 22

Using the menus (Continued)

Default setting 2 menu

Item

 

Description

 

 

 

 

 

Projection

Sets projection mode in accordance with Placement Style. p.21

 

mode

(Standard)

(Rear)

(Ceiling)

(Rear ceiling)

 

 

 

 

 

Fan mode

Sets the cooling fan speed.

 

Standard

High

Remote control When 2 projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control.

[ or : Enter setting] [: Select from 1, 2] [: Confirm]

[ :Select OK to end] Press [Cancel] to return.

Key lock

Lock the control panel buttons.

 

 

 

 

[ or

: Enter setting] [

: Select On/Off] [

: Confirm]

 

 

[

:Select OK to end]

 

 

 

 

Press [Cancel] to return.

 

 

 

Lamp power

Set the lamp power.

 

Low

Standard

 

 

 

 

 

Reset all

Press

. (The password and user logo are not reset.)

 

 

 

Resets all adjustments and settings to their factory settings. Yes

No

Password

Password setting p.33

 

 

 

 

Press

. Password registration/Password setting

 

 

Detailed description [Fan mode]

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level).

• Do not set Fan mode to [High] when using the projector at a lower altitude.

[Remote control]

Sets a remote control code from 2 types. You can set each code respectively for up to 2 projectors. The factory setting is [1].

To switch codes, set the same code for the projector and the remote control. A remote control code is applied after the setting is done.

You cannot operate the remote control if the codes of the projector and the remote control do not match.

Remote control code setting for remote control

Set the same remote control code switch as the projector. p.16 p.17

[Key lock]

Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly operation with the control panel buttons is disabled.

To release the key lock, set the [Key lock] to [Off] using remote control. Pressing the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in orange for 3 seconds, and at the same time the projector beeps.).

[Lamp power]

When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter.

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

 

 

 

“Yes”: displayed, “No”: not displayed

 

 

 

 

 

 

 

 

 

 

 

Item

Description

Digital (DVI)

Analog (D-SUB)(DVI)

Video

S-video

 

 

 

 

 

 

 

 

RGB

Y/PB/PR

RGB

Y/PB/PR

 

 

 

 

 

 

 

 

 

 

 

Input

Input source name

Yes

Yes

Yes

Yes

Yes

Yes

 

 

 

 

 

 

 

 

 

 

 

 

Mode name

RGB input mode [Note 1]

Yes

No

Yes

No

No

No

 

 

Resolution

Resolution (in dots)

Yes

No

Yes

No

No

No

 

Operations

 

 

 

 

 

 

 

 

 

Lamp reset count

The count for lamp replacement

Yes

Yes

Yes

Yes

Yes

Yes

 

Frequency

Sync frequency

Yes

No

Yes

No

No

No

 

 

Sync

Sync signal polarity [Note 2]

Yes

No

Yes

No

No

No

 

 

Signal format

Y/PB/PR signal format

No

Yes

No

Yes

No

No

 

 

Video mode

Color method of video signal

No

No

No

No

Yes

Yes

 

 

 

 

 

 

 

 

 

 

 

 

Lamp time

Time of lamp use [Note 3]

Yes

Yes

Yes

Yes

Yes

Yes

 

 

 

 

 

 

 

 

 

 

 

 

Total time

The total time that this

Yes

Yes

Yes

Yes

Yes

Yes

 

 

projector is used.

 

 

 

 

 

 

 

 

 

 

 

Version

Firmware version [Note 4]

Yes

Yes

Yes

Yes

Yes

Yes

 

 

Notes

1:The mode of supported RGB signals p.53 is shown.

2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a dealer about getting replacement for:

TLPLW40 (sold separately).

4:[Version] shows the version of the projector’s internal control program. This version will be requested for customer service purposes.

Note

The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again.

42

43

Image 22
Contents TDP-T420 TDP-T360 Safety Precautions USA onlyImportant Safety Instructions Important Safety Instructions Place and Manner of Installation Power Supply InformationImportant Precautions Moisture CondensationExemption Clauses Remote Control BatteriesOther Information Contents Checking the package contents Names of each part on the main unitNames of each part on the control panel and remote control Label location Loading dry-cell batteries into the remote control  Operating the remote ControlOperating a computer using the remote control PlacementConnection Before connection Turning the power off Press the ON/STANDBY button Turning the power on and off Turning the power on Turn on the main power switch Turn off the main power switch Replace the lens capBasic operations Basic operations Using handy featuresUsing auto setting For computer input only Correcting the keystone distortion Zooming out the images Using handy features Resizing image  Cutting off the picture and sound temporarily Mute  Changing picture mode Setting the password How to change password  Changing screen size Setup using the Setting display Using the menusHow to set password from Off to On How to operate when password is On The image adjustment menu Using the menus The position adjustment menu  The display setting menu Default setting menu Lamp power Detailed description Fan modeRemote control code setting for remote control  Displaying Information Status displayUnplug power cord Wait until lamp is sufficiently cooled Lamp replacement When the lamp is broken About lampLamp replacement  Main unit cleaning Lens and main unit cleaning Lens cleaning Trouble indicationsTroubleshooting  List of supported signals RGB signals Specifications List of general specifications Specification List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Pin assignment of Computer 2 in & Monitor terminals Pin assignment  Main Commands Control terminal  Interface format