Toshiba TDP-T420 owner manual Important Safety Instructions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This unit is fully transistorized and does not contain any parts that can be repaired by the user.

WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read Owner’s Manual

3. Source of Light

After unpacking this product, read

Do not look into the lens while the

the owner's manual carefully, and

lamp is on. The strong light from

follow all the operating and other

the lamp may cause damage to

instructions.

your eyesight.

5. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub,

wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a

swimming pool and the like.

8.Be sure that you firmly insert the plug into the wall

outlet.

Incorrect or faulty connections may result in fire or electric shock. Avoid using an unsound or loose outlet.

9. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Before Using

2. Power Sources

This product should be operated only from the type of power source which does not exceed the voltage range specified on the rating label and the power cord.

If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

4. Ventilation

Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. Never block an opening by placing the product on a bed, sofa, rug or other similar surface. Do not place it in a built-in installation such as

abookcase or rack, unless proper ventilation is provided.

7. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Always use a soft cloth for cleaning.

10. Overloading

Do not overload wall outlets. To reduce the risk of electric shock, do not use the polarized plug with an extension cord , receptacle, or other outlet unless the blades can be inserted completely with three- wire grounding type to prevent blade exposure. Failure to follow these instructions may result in fire or electric shock.

Image 3
Contents TDP-T420 TDP-T360 USA only Safety PrecautionsImportant Safety Instructions Important Safety Instructions Moisture Condensation Power Supply InformationImportant Precautions Place and Manner of InstallationRemote Control Batteries Exemption ClausesOther Information Contents Names of each part on the main unit Checking the package contentsLabel location Names of each part on the control panel and remote control Operating the remote Control  Loading dry-cell batteries into the remote controlPlacement Operating a computer using the remote controlBefore connection ConnectionTurn off the main power switch Replace the lens cap Turning the power on and off Turning the power on Turn on the main power switch  Turning the power off Press the ON/STANDBY buttonBasic operations Correcting the keystone distortion Using handy featuresUsing auto setting For computer input only Basic operationsUsing handy features  Zooming out the images Resizing image  Changing screen size  Changing picture mode Setting the password How to change password  Cutting off the picture and sound temporarily MuteHow to operate when password is On Using the menusHow to set password from Off to On  Setup using the Setting displayUsing the menus  The image adjustment menu The position adjustment menu  The display setting menu Default setting menu  Displaying Information Status display Detailed description Fan modeRemote control code setting for remote control Lamp powerAbout lamp Lamp replacement When the lamp is broken Unplug power cord Wait until lamp is sufficiently cooledLamp replacement Trouble indications Lens and main unit cleaning Lens cleaning  Main unit cleaningTroubleshooting Specification Specifications List of general specifications  List of supported signals RGB signals Pin assignment of Computer 2 in & Monitor terminals Specifications List of supported signals Component signals  List of supported signals Video, S-Video signals Interface format  Main Commands Control terminal  Pin assignment