Toshiba B-SX4T-QQ owner manual A1.3.2 Detection Area of the Transmissive Sensor, Label

Page 39

APPENDIX 1 SPECIFICATIONS

ENGLISH VERSION EO1-33034

 

A1.3 Media

 

 

A1.3.1

Media Type (Cont.)

 

 

 

[Unit: mm]

 

 

Label dispensing mode

Batch mode

Strip mode

Cut mode

 

 

Item

 

 

Rotary cutter (*2)

Swing cutter

 

 

 

 

 

 

 

 

 

 

 

 

 

cMedia pitch

Label

10.0 – 1500.0

25.4 – 1500.0

3”/sec., 6”/sec.: 38.0 - 1500.0

38.0 – 1500.0

 

Tag

10.0 – 1500.0

----

3”/sec., 6”/sec.: 30.0 – 1500.0

25.4 – 1500.0

 

d

 

 

eMedia length

 

8.0 – 1498.0

23.4 – 1498.0

3”/sec., 6”/sec.: 25.0 – 1498.0

25.0 – 1498.0 (*1)

 

fWidth including backing paper (See NOTE 5.)

30.0 – 112.0

50.0 – 112.0

30.0 – 112.0

 

 

gLabel width (See NOTE 5.)

 

27.0 – 109.0

47.0 – 109.0

27.0 – 109.0

 

 

hGap length

 

2.0 – 20.0

6.0 – 20.0

 

 

iBlack mark length (Tag paper)

 

 

2.0 – 10.0

 

 

Effective print width

 

 

 

10.0 – 104.0 ±0.2

 

 

jEffective print length

Label

6.0 – 1496.0

21.4 – 1496.0

3”/sec., 6”/sec.: 23.0 - 1496.0

23.0 – 1496.0

 

Tag

8.0 – 1498.0

----

3”/sec., 6”/sec.: 28.0 – 1498.0

23.0 – 1498.0

 

k

 

 

Print speed up/slow down area

 

 

1.0

 

 

Thickness

 

Label

 

 

0.13 – 0.17

 

 

 

Tag

 

 

0.15 – 0.29

 

 

 

 

 

 

 

 

Maximum effective length for on the fly issue

 

 

1361.0

 

 

Maximum outer roll diameter

 

 

 

Ø 200

 

 

Roll direction

 

 

 

Inside

 

 

Inner core diameter

 

 

 

Ø 76.2±0.3

 

NOTES:

1.To ensure print quality and print head life use only TOSHIBA TEC specified media.

2.The media length specifications for use of the cutter are:

*1: When issuing a label using the swing cutter, label length should be 35.0 mm – (Gap length/2).

*2: The rotary cutter does not support the print speed of 10”/sec.

When using the Rotary Cutter, be sure to install the Ribbon Saving Module (B-9904-R-QM). Failure to do this may cause a paper jam or ribbon error.

3.When marking black marks on the label rolls, they should be marked at the gaps.

4.“On the fly issue” means that the printer can feed and print without stopping between labels.

5.There are restrictions in use of the media which is narrower than 50 mm. For details, refer to TOSHIBA TEC service representative.

A1.3.2 Detection Area of the Transmissive Sensor

The Transmissive Sensor is movable from the centre to the left edge of media.

The Transmissive Sensor detects a gap between labels, as illustrated below.

<Label>

 

 

 

 

 

 

 

Area to be detected.

 

 

 

 

 

 

 

Centre of media

 

Sensor position

 

 

 

 

 

 

 

 

 

 

Print side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. 2.0 mm

 

 

 

 

 

 

 

 

 

 

 

Label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Min. 6.0 mm when using

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the cutter module.)

 

 

 

 

 

 

 

 

 

 

 

Label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. 12 mm

 

 

 

 

 

 

 

 

 

 

 

Media feed direction

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sensor is movable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

within this range.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EA1- 3

Page 38 Page 40
Image 39
Page 38 Page 40
Contents SX4T-QQ/QP Vorsicht CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Introduction Features Product OverviewUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Gori Connecting the Cables to Your PrinterConnecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media @ ?Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionBatch mode Strip modeSTANDARD/PEEL OFF position Cut mode Build-in rewinder modeLoading the Ribbon Auto Ribbon Saving ModePcmcia Cards Test Print 3517Feed or Restart key Printer’s power OFF then back to on and check that the LCD Sample of the bar code test print label Operation Panel On Line ModeOperation Reset Dump Mode Maintenance CleaningPrint Head/Platen/ Sensors Optional Cutter Module Covers and PanelsCare/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Do not use any tool that may damage the Print Head Removing Jammed MediaThreshold setting procedure Threshold SettingAppendix 1 Specifications A1.1 PrinterModel Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeLabel A1.3.2 Detection Area of the Transmissive SensorA1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaTag paper with square holes Figure below shows the effective print area on the media A1.4 RibbonAppendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples CODE39 Full Ascii Interleaved 2 CODE39 StandardJAN13, EAN13 EAN13+2 digits EAN13+5 digitsRSS Limited UPC-A+5 digitsIndustrial 2 RSS-14 RSS-14 StackedBar code GlossariesUSB Universal Serial Bus Print head elementIndex Index Page Page EO1-33034

B-SX4T-QQ specifications

The Toshiba B-SX4T-QQ is a robust and versatile industrial printer designed to meet various labeling and printing needs across diverse industries. This printer stands out for its compact design, making it suitable for environments where space is at a premium. With its advanced features and technologies, the B-SX4T-QQ provides exceptional performance and reliability.

At the heart of the B-SX4T-QQ is its high-resolution printing capability. It offers a print resolution of up to 300 dpi, which guarantees crisp and clear labels, barcodes, and graphics. This high resolution is vital for applications requiring fine detail, such as small labels used in electronics or pharmaceuticals.

One of the most remarkable features of the B-SX4T-QQ is its dual-technology printing capability. It can operate with both thermal transfer and direct thermal printing methods, providing flexibility for various labeling materials and applications. This adaptability allows users to choose the best printing method based on the specific media and the intended use of the labels.

The printer is equipped with a fast processing speed, capable of producing high-quality prints at a rate of up to 6 inches per second. This efficiency is essential for high-volume printing environments, where time and productivity are critical. Accompanied by a large media capacity, the B-SX4T-QQ minimizes downtime caused by the need for frequent media replacement.

Connectivity is another highlight of the Toshiba B-SX4T-QQ. It supports multiple interfaces, including USB, serial, and Ethernet, facilitating seamless integration with existing systems and networks. This versatility makes it compatible with various operating environments, enhancing workflow efficiency.

The B-SX4T-QQ is built with durability in mind. Housed in a rugged casing, it is designed to withstand the rigors of industrial use. Its reliable performance is further enhanced by enhanced features such as a user-friendly LCD display and intuitive control panel, making operation and monitoring straightforward.

In terms of software compatibility, the printer supports multiple programming languages, including PPL and ZPL, which ensures ease of integration with various applications. This capability is particularly beneficial for businesses that require custom label designs and specific printing configurations.

Overall, the Toshiba B-SX4T-QQ is an excellent choice for businesses looking for a reliable, versatile, and high-performance industrial printer. Its combination of advanced features, robust design, and ease of use positions it as a valuable asset in any labeling operation.
Top Page Image Contents