Toshiba B-SV4D owner manual Print test label sample

Page 20

2. PRINTER SETUP

ENGLISH VERSION EO1-33061

2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities

2.7.2Self Print Test and Dump Mode (Cont.)

NOTE:

The following commands should not affect the test print issue.

D, AX, XS, Z2;1, Z2;2 (without AY)

Print test label sample

PRINTER INFO.

 

PROGRAM VERSION

VX.XX XXXX

TONE ADJUST

+XX

FEED ADJUST

+XX.Xmm

CUT POSITION ADJUST

+XX.Xmm

BACKFEED ADJUST

+XX.Xmm

PARAMETER

[PC-850][0]

 

[9600][8][1][NONE][0]

 

[ON][AUTO][FEED][B0]

X-COORDINATE ADJUST

+XX.Xmm

SENSOR

TRANSMISSIVE [17]

MEMORY

[192KB][XXXKB]

TTF AREA

[XXXKB][XXXKB]

EXT CHAR AREA

[XXXKB][XXXKB]

BASIC AREA

[XXXKB][XXXKB]

PC SAVE AREA

[XXXKB][XXXKB]

INFORMATION

XXXXXXXXXXXXXXXXXXX

TOTAL FEED

X.XXKm

IP ADDRESS

XXX.XXX.XXX.XXX

SUBNET MASK

XXX.XXX.XXX.XXX

GATEWAY

XXX.XXX.XXX.XXX

DHCP

Enable

 

 

 

 

 

 

The test print contents should be changed by the following commands and parameters:

PROGRAM VERSION: VX.XX XXXX ---

Firmware version and checksum

TONE ADJUST: +XX -------------------------

Print tone fine adjustment value

FEED ADJUST: +XX.Xmm ------------------

Print position fine adjustment value

CUT POSITION ADJUST: +XX.Xmm -----

Cut position fine adjustment value

BACKFEED ADJUST: +XX.Xmm ----------

Back feed amount fine adjustment value

PARAMETER: [PC-850][0] -----------------

Character code selection and Font “0”

 

selection

[9600][8][1][NONE][0] ---

Baud rate, Data length, Stop bit length,

 

Parity, and Transmission control of RS-

 

232C

[ON][AUTO][FEED][B0]

Forward feed wait function, Control code,

 

Feed key function, and Euro code

X-COORDINTE ADJUST: +XX.Xmm -----

X-coordinate fine adjustment value

SENSOR: TRANSMISSIVE [17] ------------

Sensor selection and sensitivity

MEMORY: [192KB][XXXKB]---------------

Memory capacity of the Main PC Board and

 

optional memory card (0,1,2,3,4,6,8)

TTF AREA: [XXXKB][XXXKB]------------

True type font storage area, Main PC board

 

and optional memory card

EXT CHAR AREA: [XXXKB][XXXKB] --

Writable character storage area, Main PC

 

board and optional memory card

BASIC AREA: [XXXKB][XXXKB] --------

BASIC file storage area, Main PC board and

 

optional memory card

PC SAVE AREA: [XXXKB][XXXKB] -----

PC save storage area, Main PC board and

 

optional memory card

E2-10

Image 20
Contents SV4D Series CE Compliance for EU only VorsichtSV4D Series Safety Summary Meanings of Each SymbolPrecautions Table of Contents Product Overview Introduction Features UnpackingAccessories When purchasing the power cord SVT H05VV-FFront View Rear View DimensionsAppearance Button and Indicator Lamp InteriorPrinter Setup PrecautionsTurning on the Printer Procedure before OperationTurning the Printer Connecting the Cables to the Printer Turning OFF the PrinterConnecting the Power Adapter and the Power Cord Loading the Media Media Guide Adjustment Knob Strip mode Option External Media Roll Hanger Option Test, and Dump Mode different type Utilities Self Print Test and Dump ModeMedia Sensor Media Sensor CalibrationPrint test label sample E2-11 Print Head MaintenanceCleaning Platen/Sensors CoverCare/Handling of the Media Removing Jammed Media TroubleshootingTroubleshooting Guide Appendix 1 Specifications A1.1 PrinterA1.3.1 Media Type A1.2 OptionsA1.3 Media A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area Figure below shows the effective print area on the mediaAppendix 2 Interface Interface CablesGlossaries Bar codeIndex Index EO1-33061A
Related manuals
Manual 31 pages 27.26 Kb