Toshiba B-EV4T owner manual Media Sensor, Test, and Dump Mode different type Utilities

Page 28

2. PRINTER SETUP

ENGLISH VERSION EO1-33087

2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities

2.9 Media Sensor

This utility is used to calibrate the sensitivity of the Feed Gap/Black

 

Mark Sensor.

Calibration, Self Print It is necessary to set the media sensors after the media is changed to

Test, and Dump Mode different type.

Utilities

2.9.1Media Sensor Calibration

NOTE:

The sensor type used in the last print job has been selected.

1.First, select the sensor to calibrate in the following procedure.

Turn on the printer power.

Open the Top Cover.

The factory default is the Feed Gap Sensor.

When the Indicator Lamp is unlit, hold down the [FEED] Button for 5 sec. or more, and release when the lamp lights up in green.

The Indicator Lamp repeatedly lights up in different colours at approx. 1.5 sec. interval. When the lamp lights up in the colour representing the target sensor type, press the [FEED] Button.

The Indicator Lamp

 

 

[FEED] Button

 

lights up in green.

 

 

 

 

 

 

 

 

 

 

 

 

 

About 3 seconds.

 

 

 

 

 

 

 

The Indicator Lamp

 

 

[FEED]

 

 

lights up in orange.

 

 

Button

 

 

 

 

 

 

 

 

 

About 3 seconds.

The Indicator Lamp is unlit. (Reflective (Black Mark) Sensor is selected.)

The Indicator Lamp is unlit. (“No sensor” is selected.)

The Indicator Lamp

[FEED] Button

lights up in red. About 3 seconds.

The Indicator Lamp is unlit. (Transmissive (Feed Gap) Sensor is selected.)

2.Turn off the printer, load the media properly, and close the Top Cover. Note: Do not place pre-printed area above the media sensor, as doing so disables a correct sensor calibration.

3.To calibrate the Black Mark Sensor, align the sensor position with the black marks on the media. (Refer to Section 2.7.)

4.Press the [FEED] Button while turning on the printer. The Indicator Lamp will light up in the following order:

Green (Flashing) → Red (Flashing) → Orange (Flashing) → Orange → RED → Green

5.Release the [FEED] button when the indicator lamp lights up in red. The printer automatically feeds the media to perform a sensor calibration.

Note: If you failed to release the [FEED] button at the right timing, retry from Step 4.

6.To start the Online operation, turn the printer off, then on again.

E2-17

Page 27 Page 29
Image 28
Page 27 Page 29
Contents EV4T Series CE Compliance for EU only VorsichtSafety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA2-1 For EU onlyIntroduction Features Unpacking Accessories Product OverviewWhen purchasing the power cord SVT H05VV-FFront View DimensionsRear View Interior Button and Indicator Lamp Printer statusPrinter Setup PrecautionsTurning the Printer Procedure before OperationTurning on the Printer Turning OFF the Printer Connecting the Cables to the Printer Connecting the Power Adapter and the Power Cord To open the Top Cover Opening/Closing the Top CoverTo close the Top Cover Loading the Media Open the Media Holders 1 Media Sensor Calibration Batch mode Strip mode Option How to set the mediaHow to Load Fanfold Paper Stock Cut mode OptionExternal Media Roll Hanger Option Loading the Ribbon BrokenPrint Head Block Ribbon Access Cover Close the Ribbon Access Cover until it clicks Media Sensor Test, and Dump Mode different type UtilitiesMedia Sensor Calibration Self Print Test and Dump Mode Print test label sampleE2-19 „ Inserting an SD Card How to Use an SD Card„ Removing an SD Card Cleaning MaintenancePrint Head Platen/Sensors Media HousingCover Care/Handling of the Media and Ribbon OptionTroubleshooting Troubleshooting GuideColor Status Cause Solutions Status LampRemoving Jammed Media Appendix 1 Specifications A1.1 PrinterEV4T-TS14-QM-R A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Figure below shows the effective print area on the mediaAppendix 2 Interface Interface CablesGlossaries Bar codeSupply EO1-33087C

B-EV4T specifications

Toshiba B-EV4T is a versatile and robust thermal transfer printer designed for various industries, including retail, logistics, and manufacturing. This printer stands out for its impressive performance, reliability, and user-friendly features, making it an ideal choice for businesses requiring efficient label printing solutions.

One of the main features of the B-EV4T is its compact design, which allows it to fit into tight workspaces without sacrificing performance. Despite its small footprint, the printer delivers high-quality printing at speeds of up to 200mm per second, ensuring that users can complete their labeling tasks quickly and efficiently.

The B-EV4T is equipped with advanced thermal transfer printing technology, enabling it to produce sharp, clear images and crisp text. This technology ensures that labels are durable and resistant to fading, making them suitable for both indoor and outdoor applications. The printer supports a wide range of media types, including paper, synthetic materials, and various label sizes, providing flexibility for diverse printing needs.

Another noteworthy characteristic of the B-EV4T is its ease of use. The printer features a user-friendly interface and an intuitive LCD display that simplifies operation and maintenance. Users can easily navigate through settings and perform tasks such as adjusting print density and label width. Additionally, the modular design of the printer allows for easy access to components, making it straightforward to load media and replace ribbons.

Connectivity is a crucial aspect of modern printers, and the B-EV4T does not disappoint. It offers multiple connectivity options, including USB, Ethernet, and serial interfaces. This versatility allows seamless integration with various systems and networks, ensuring that the printer can be easily incorporated into existing workflows.

The printer is also designed with energy efficiency in mind, reducing power consumption without compromising performance. This not only helps businesses save on energy costs but also contributes to a more sustainable operational approach.

In summary, Toshiba's B-EV4T thermal transfer printer is a reliable and efficient solution for businesses requiring high-quality label printing. With its compact design, advanced printing technology, user-friendly features, and versatile connectivity options, the B-EV4T stands out as a top choice for meeting diverse labeling demands across multiple industries.
Top Page Image Contents