Toshiba VF-AS1 Series, RS485 Input terminal board status FD06, FE06, Res, BIT15, Bit0 FE06

Page 51

E6581315

Input terminal board status (FD06, FE06)

Input terminal board status (current status): “Communication Number FD06”

Input terminal board status (status immediately before the occurrence of a trip): “Communication Number FE06”

Using terminal function selection parameters, functions can be assigned individually to the termi- nals on the input terminal board.

If a terminal function selection parameter is set to 0 (no function assigned), turning on or off the cor- responding terminal does not affect the operation of the inverter, so that you can use the terminal as you choose.

When using a terminal as a monitoring terminal, check beforehand the function assigned to each terminal.

Data composition of input terminal board status (FD06, FE06)

	Bit	Terminal name	Function (parameter title)	0	1
	0	F	Input terminal function selection 1 (f111)
	1	R	Input terminal function selection 2 (f112)
	2	ST	Input terminal function selection 3 (f113)
	3	RES	Input terminal function selection 4 (f114)
	4	S1	Input terminal function selection 5 (f115)
	5	S2	Input terminal function selection 6 (f116)
	6	S3	Input terminal function selection 7 (f117)
	7	S4	Input terminal function selection 8 (f118)	OFF	ON
	8	L1	Input terminal function selection 9 (f119)	OFF	ON
	8	L1	Input terminal function selection 9 (f119)
	9	L2	Input terminal function selection 10 (f120)
	10	L3	Input terminal function selection 11 (f121)
	11	L4	Input terminal function selection 12 (f122)
	12	L5	Input terminal function selection 13 (f123)
	13	L6	Input terminal function selection 14 (f124)
	14	L7	Input terminal function selection 15 (f125)
	15	L8	Input terminal function selection 16 (f126)

Example: Data set for FE06 when the F and S1 terminals are ON = 0011H

	BIT15																	bit0
FE06:		0	0	0	0	0	0		0	0	0	0	0	1	0	0		0	1
			0					0				0					9

50

Image 51

Contents E6581315② Tosvert VF-AS1 Series RS485 Communication FunctionE6581315 Read first Safety precautionsContents General outlines of the communication function BIT15 BIT8BIT7 BIT0Bit Word BIT2 Data transmission specificationsCommunication protocol About the handling of received framesMOUBUS-RTU Toshiba Inverter Protocol Binary mode 2FHData Data transmission format used in Ascii modeData transmission format INV-NO CMD28H Bytes Checksum area 5bytes BlankData SUM INV-NOData transmission format used in binary mode Sum 1 bytes Checksum not omissible 00H to FFH Command receivedReturned for the 57H W and 50H P commands Byte Bytes2FH Byte 4EH6EH Bytes NornTransmission format of Block Communication Page Bytes Blank Start Code INV-NO Block communication Computer Inverter CommandsDummy data is required for this command Reads the data with the specified communication numberRFE03077BCR RFE03CRPage Transmission errors Format error Data transmission format does not matchCommunication There is no communication number that matches Broadcast communication function VF-AS1 RFC90CR Examples of the use of communication commandsAscii mode Computer → Inverter Inverter → Computer From the computer H = 24d  trip statusExamples of Communication programs Goto =LENS$ For I=1 to LNext Input #1,B$160 T=TIMER COUNT=TIMER-T If Count 0 then T=TIMERPrint #1,B$ Page End If MSComm1.Output = Text2.Text & Chr13 End SubText2.Text = Text1.Text = End Sub Inverter number  MODBUS-RTU protocolRead command MODBUS-RTU transmission formatCRC Text size is 8 bytes fixed Inverter Write commandBlank Command 1 byte 5bytes Blank Command 1 byteEnd Return CRC Error codesCRC Generation Bit counter =Inter-drive communication Never use pin-7 P11 QWiring 4-wire RS485 communication） E6581315 QWiring 2-wire RS485 communicationPage Parameters relating to the slave side example =0.01% Proportional control of speed80.00Hz 40.00Hz Slave 100.00Hz 00%90.00Hz 45.00Hz Slave 100.00Hz1 00%INV-NO 1 byte Inverter number Transmission format for inter-drive communication0OFF Communication parametersMODBUS-RTU Inverter number Baud rate,  , Parity INV INV → PC PC → INV „ Timer Time-out period Computer linkPC → INV Master INV To SlaveSend waiting time ,  Free notesUse this function for the following case OFF Commands and monitoring from the computerCommunication commands commands from the computer PI OFFBraking answer BA Electric Power quantityForcibly braked Preliminary excitation Brake release B Wire RS485 communication FA32 Output terminal no Specified data output „ Terminal board output data FA50„ FM analog output FA51 „ AM analog output FA52Monitoring from the computer RFD00CRUnit 0.01% N·m BIT15 „ Input terminal board status FD06, FE06RES Input terminal function selection 9 f119„ Output terminal board status FD07, FE07 ST=ON ST=OFF „ Inverter operating status 1 FD01, FE01„ Inverter operating status 3 FD49, FE49 „ Inverter operating status 2 FD42, FE42„ Inverter operating command mode status FD45, FE45 „ Inverter operating frequency mode status FD46, FE46Preset speed operation „ Alarm information monitor FC91 „ Cumulative operation time alarm monitor FE79Bit Specifications Remarks E6581315 Model Data „ Inverter model capacity code FB05LED setting by communication Parameter Name Range SettingUtilizing panel LEDs and keys by communication „ Block Communication Function for LED Display Blank Ascii LED display data code 00H-1FH are blankKey utilization by communication FA10=0FA10=1 Parameter data ROM EEPPage FE29 Input power Alarm codeFE02 Frequency command value 01Hz FE19 Torque commandTion FE80 Cumulative power on time E6581315 FD50 Light-load high-speed torque 01%FE84 Binary input value option ESC Appendix 1 Table of data codesCan SUBResponse time „ Data transmission time Appendix 2 Response timeVF-A7 Appendix 3 Compatibility with the communication functionAppendix 4 Troubleshooting Appendix 5 Connecting for RS485 communication TXB RXARXB TXA