Toshiba AR-B1375, 386SX SSD Drive Number SW1-3 & SW1-4, Simulate 2 Disk Drive, Flash Eprom Sram

Page 43

AR-B1375/AR-B1376 User s Guide

6.2.4 SSD Drive Number (SW1-3 & SW1-4)

The AR-B1375/AR-B1376’s SSD can simulate one or two disk drives. You can assign the drive letter of the AR- B1375/AR-B1376 by configuring SW1-3 & SW1-4.

You can make the computer to boot from SSD by copying DOS into the SSD. If your SSD does not have DOS, the computer will boot from your hard disk or floppy disk. In this condition, the SSD BIOS of AR-B1375/AR-B1376 will set the drive letter of the SSD to the desired drive letter automatically.

The SSD BIOS will simulate one disk drive when only (FLASH) EPROM or SRAM (starting from MEM1 socket) is installed. The drive numbers with respect to the switch setting when the AR-B1375/AR-B1376 simulates single disk drives.

SW1-3

SW1-4

Occupies floppy disk number (SSD)

OFF (*)

OFF

0 or 1 (Note 1)

ON

OFF

0 or 2 (Note 2)

OFF

ON

0

ON

ON

0

Table 6-3 SSD Drive Number

NOTE: 1. If there is no DOS on this SSD, the disk number will 1 (B:). If any DOS is found by the AR-B1375/AR- B1376 SSD BIOS, the disk number will be 0 (A:) But, you can change the disk number from 0 to 1 by pressing the <ESC> key during system bootup.

2.If there is no DOS on this SSD, the disk number will be 2 (C: or D: or…). If any DOS is found by AR- B1375/AR-B1376 SSD BIOS, the disk number will be 0 (A:). But, you can change the disk number from 0 to 2 by pressing the <ESC> key during system bootup.

(1)Simulate 2 Disk Drive

When (FLASH) EPROM and SRAM are both used on the AR-B1375/AR-B1376, or you only have installed SRAM that does not start from MEM1 socket, the AR-B1375/AR-B1376 will simulate two disk drives. The drive numbers respect to those switch settings when AR-B1375/AR-B1376 simulates two disk drives.

SW1-3

SW1-4

Occupies floppy disk number

FLASH (EPROM)

SRAM

 

 

OFF

OFF

0 or 1 (Note 1)

2

ON

OFF

0 or 2 (Note 2)

3

OFF

ON

0

1

ON

ON

0

2

Table 6-4 SSD Drive Number for Simulate 2 Disk Drive

NOTE: 1. If there is no DOS on this SSD, the disk number will be 1 (B:). If any DOS is found by the AR-B1375/AR- B1376 SSD BIOS, the disk letter will be 0 (A:). But, you can change the disk number from 0 to 1 by pressing the <ESC> key during system bootup.

2.If there is no DOS on this SSD, the disk number will be 2 (C: or D: or….). If any DOS is found by the AR-B1375/AR-B1376 SSD BIOS, the disk number will be 0 (A:). But, you can change the disk number from 0 to 2 by pressing the <ESC> key during system bootup.

6-3

Image 43
Contents 386SX CPU Card Page Table of Contents Programming RS-485 & Index Bios ConsoleSpecifications & SSD Types Supported Using Memory Banks Placement & DimensionsPreface Organization Static Electricity PrecautionsIntroduction OverviewPacking List Features DMA Controller System ControllerMicroprocessor DMA ControllerInterrupt Controller Keyboard ControllerI/O Port Address Map 1 I/O Port Address Map2 I/O Channel Pin Assignment Bus Hex Range DeviceI/O Channel Pin Assignments Real-Time Clock & Non-Volatile RAM TimerREAL-TIME Clock and NON-VOLATILE RAM Address DescriptionTransmitter Holding Register THR Interrupt Enable Register IERSerial Port Receiver Buffer Register RBRModem Status Register MSR Line Control Register LCRModem Control Register MCR Line Status Register LSRPrinter Interface Logic Parallel PortDivisor Latch LS, MS Register AddressPrinter Status Buffer Error Slct PE -ACK -BUSYPrinter Control Latch & Printer Control Swapper Page Overview Setting UP the SystemAUX. Keyboard Connector J4 System SettingKeyboard Connector Pin Mini DIN Keyboard Connector CN3Pin PC/104 Connector Bus C & D CN1 2 PC/104 ConnectorPin PC/104 Connector Bus a & B CN2 Name Description O Channel Signal DescriptionHDD Pin Assignment Hard Disk IDE Connector CN4I/O Channel Signal’s Description Pin SignalParallel Port Connector CN6 FDD Port Connector CN5CN6 External RS-485 Adapter Select J6 & J7 Serial PortRS-232/RS-485 Select for COM-B JP2 RS-485 Terminator JP7LED Header Reset Header J1RS-232 Connector CN7 & DB2 External Power LED Header J2External Speaker Header J5 Power Connector J3External Battery Battery Charger Select JP3SIMM1 SIMM2 Dram ConfigurationExternal Battery Connector J11 CPU Base Clock Select JP1IRQ 9 Used Select Connecting the CRT MonitorVGA Setting JP5 CRT/LCD Flat Panel DisplayLCD Flat Panel Display CRT Connector DB1Inverter Board Description LCD ConnectorDE/E Signal from M or LP Select JP6 JP6 LCD Control Connector CN9Manufacture Model No Description LCD Panel Display Connector CN8Supported LCD Panel LCD Display AssignmentUtility Diskette InstallationStep VGA DriverWIN 3.1 Driver WIN 95 DriverSSD Utility RFG.EXE RFGDEMO.PGF Write Protect FunctionSoftware Write Protect Enable the Software Write ProtectDisable the Software Write Protect Hardware Write ProtectLED Watchdog TimerWatchdog Timer Setting Time-Out SettingWatchdog Timer Trigger Watchdog Timer EnabledWatchdog Timer Disabled Solid State Disk Switch SettingDEVICE=C\DOS\EMM386.EXE X=C800-C9FF Overview2 I/O Port Address Select SW1-1 SSD Firmware Address Select SW1-2Simulate 2 Disk Drive SSD Drive Number SW1-3 & SW1-4Flash Eprom Sram Disk Drive Name Arrangement ROM Type Select SW1-5 & SW1-6M1~M3 & JP4 Memory Type Setting Jumper SettingSwitch and Jumper Setting ROM Disk InstallationUV Eprom 27Cxxx Software Programming Large Page 5V Flash DiskJP4 \PGM137X ROM pattern file name Small Page 5V Flash ROM Disk Using Tool ProgramRAM Disk Typing DOS Command\FORMAT RAM disk letter /U Combination of ROM and RAM DiskPage Bios Setup Overview Bios ConsoleHard Disk Setup Standard Cmos SetupDate & Time Setup Floppy SetupAdvanced Cmos Setup System Keyboard Password CheckWait for ‘F1’ If Error Hard Disk DelayAdvanced Chipset Setup Load Default Setting Password SettingSetting Password Password CheckingBios Update Auto Configuration with Fail Safe SettingBios Exit Save Settings and ExitFile of AMIFLASH.EXE had to Version Specifications Specifications & SSD Types SupportedSSD Types Supported Fujitshu AtmelSST WinbondSocket Using Memory BanksRegister Port CS1 CS0Page Placement Placement & DimensionsDimensions Send out one character Transmit Programming RS-485 & IndexProgramming RS-485 Initialize COM portINPSTR$ Return OUT &H3FC, INP%H3FC and &HFA ReturnPrint #1, OUTCHR$ OUT &H3FC, INP&H3FC and &HEF ReturnName Function

386SX, AR-B1376, AR-B1375 specifications

The Toshiba AR-B1375 and AR-B1376 are notable embedded computing solutions that incorporate the 386SX microprocessor architecture. Designed for various applications, these models focus on reliability, performance, and versatility, making them appealing choices for system integrators and developers.

At the core of the AR-B1375 and AR-B1376 is the Intel 386SX microprocessor. This landmark processor marked a significant advancement in computing technology, introducing a 32-bit architecture while maintaining compatibility with 16-bit applications. The 386SX is known for its efficient processing capabilities, offering both multitasking support and enhanced memory management. It operates at clock speeds ranging typically from 16 MHz to 25 MHz, contributing to its effectiveness in running industrial applications.

One of the key features of the AR-B1375 and AR-B1376 systems is their modular architecture, which allows for easy customization and expansion. This modularity means users can tailor the hardware according to specific requirements, making it suitable for a wide range of applications such as automation, telecommunications, and embedded systems.

Both models support various I/O options, ensuring seamless integration with peripherals and external devices. They typically come equipped with serial and parallel ports, as well as support for modern interfaces like USB. The systems also feature onboard expansion slots, enabling the addition of further functionality, such as additional memory or specialized processing units.

In terms of memory, the AR-B1375 and AR-B1376 support a range of RAM configurations, allowing users to scale their systems based on the application demands. The inclusion of EPROM and EEPROM options also facilitates easy updates and programmability, which is crucial for embedded systems that often require firmware adjustments over time.

Moreover, these models are known for their robust thermal management features, which are essential in industrial environments where conditions can be harsh. This capability ensures stable performance and longevity, reducing the risk of system failures due to overheating or environmental factors.

To summarize, the Toshiba AR-B1375 and AR-B1376, coupled with the 386SX microprocessor, offer a blend of performance, flexibility, and reliability. Their modular design, extensive I/O support, and memory scalability make them ideal for a variety of embedded computing applications, placing them as commendable options in the world of industrial computing solutions. These systems not only exemplify Toshiba's commitment to innovation but also contribute significantly to the functionality of embedded technologies in a rapidly evolving industry.