D-Link DSL-G664T manual Wireless Settings, Wireless configuration window

Page 29

Wireless Settings

Click the Enable AP box to allow the router to operate in the wireless environment.

SSID: The SSID identifies members of Service Set.

Accept the default name or change it to something else. If the default SSID is changed, all other devices on the wireless network must use the same SSID.

Channel: What channels are available for use by the access point depends on the local regulatory environment. Remember that all devices communicating with the device must use the same channel (and use the same SSID). Use the drop down menu to select the channel used for your 802.11g wireless LAN.

The wireless channel number is available from your Internet Service Provider (ISP).

If network Security is not used, click None, then click Apply.

Important Note: For initial configuration of the Router, make sure that None is selected. It is more important first to make sure that your wireless network is functioning properly.*

Figure 3-4. Wireless configuration window

* For information on applying various types of security to your network, see the next few pages.

21

Image 29
Contents DSL-G664T Warnung Table of Contents Advanced Router Management Before You Start Installation RequirementsAbout This User’s Guide Ethernet Port NIC Adapter 802.11b Wireless LAN ConfigurationAdditional Software About Clip Connections RFCInformation you will need from your Adsl service provider LAN Subnet Mask for the DSL-G664T Packing ListRouter Description and Operation What is ADSL?Introduction Router Features Standards Compatibility and Compliance Front Panel Display Packing ListRear Panel Connections 802.11g Wireless Introduction to 802.11b WirelessWireless LAN Basics Radio TransmissionRange Adsl TechnologyLocation Hardware InstallationFactory Reset Button Power on RouterNetwork Connections Hub or Switch to Router ConnectionConnect Adsl Line Connect Router to EthernetComputer to Router Connection WAN Configuration Summary Basic Router ConfigurationConfiguring IP Settings on Your Computer Configure Windows XP for Dhcp Windows Windows ME Configure Windows 2000 for DhcpConfigure Windows ME for Dhcp Windows 95 and Windows Windows NT 4.0 Workstations Configure Windows 95 and Windows 98 for DhcpConfigure Windows NT 4.0 for Dhcp Login to Home Access the Configuration ManagerHome Status Information window Configure the RouterOpening Setup window Setup MenuWireless configuration window Wireless SettingsWEP configuration window Wireless Security802.1X 1X configuration windowPSK String WPA Wi-Fi Protected AccessModem Setup menu change modulation type Modem SetupPPPoA Connection 1 Setup menu Configure Connection 1 for PPPoAChange the Connection Type Configure Connection 1 for PPPoE10. Setup Configure Connection 1 for PPPoE 11. Setup Configure Connection 1 for Bridge Configure Connection 1 for Bridge12. Setup Configure Connection 1 for Static IP for the WAN Configure Connection 1 for Static IP for WANPage Configure Connection 1 for Dhcp for WAN 14. Setup Configure Connection 1 for Clip IPoA Configure Connection 1 for ClipNew Connection Example 1 Create a New PPPoE Connection Create a New ConnectionNew Connection Example 2 Create a New Bridge Connection 16. Set up a New Connection ConnectionDhcp Parameter Description Start IP Dhcp Configuration for LANEnd IP Lease Time18. Configure Dhcp Relay Service Enable Dhcp RelayManagement IP 19. Configure Management IP20. Router Tools Menus Save Configuration Changes22. Changes permanently saved message Advanced Router Management Advanced setup main menuAdvanced UPnP window UPnPLAN Clients LAN Clients SetupAdvanced Port Forwarding window Port ForwardingAudio/Video Category Available Rules GamesApplications ServersSet up Custom Port Forwarding Rules Page Access Control menu Access ControlVPN DMZ IP Address Enable/Disable NAT and FirewallAdvanced Security Bridge Filters Setup Remote Management10. Multicast pass-through menu Multicast Pass-through11. Static Routing menu Static Routing12. Dynamic Routing RIP menu Dynamic RoutingMultiple Virtual Connections Wireless ManagementPage 13. Tools and utility menu links Tools and Utility Menus14. User Management menu User Management15. Tools System Commands menu System Commands16. Remote Log menu Remote Log17. Tools Update Gateway window Update Gateway18. Tools Ping Test window Ping Test19. Tools Modem Test window Modem Test20. Status display links Status Menus21. Network Statistics window Network Statistics22. Connection Status window Connection Status23. Dhcp Clients window Dhcp Clients24. Modem Status window Modem Status25. Product Information window Product Information26. System Log window System Log27. Opening Help window Help MenuTechnical Specifications CE Class B Physical and EnvironmentalUsing the Default IP Address IP Address SetupAssigning Network IP Addresses Manual IP Address AssignmentChanging the IP Address of the Router Using DhcpIP Setup Example #2 IP Addresses IP ConceptsClass Beginning Address Ending Address Subnet MaskClass a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0 IP Class Subnet MaskMicrofilters Microfilter InstallationMicrofilters and Splitters Line Splitter Line Splitter Installation