D-Link DSL-G664T manual Configure Connection 1 for Static IP for WAN

Page 38

9.To save the changes made to Connection 1, click the Tools tab and then click on the System Commands button. Click on the Save All button to store the configuration settings. Click on Back button to return to the System Commands menu.

10.Check the WAN connection status. Click the Status tab and then the Connection Status button. Look under WAN to view the State of Connection 1, it should read “ N/A”. If the WAN connection state does not appear to Connected after a few minutes, go back to the Connection 1 Setup menu, check the settings and make sure they are correct.

Configure Connection 1 for Static IP for WAN

Static is used whenever a known static IP is assigned. The accompanying information such as the Subnet mask and the gateway should also be specified in order to be able to connect. Up to three Domain Name Server (DNS) addresses can also be specified. These are the servers would enable you to have access to other web servers. Valid IP addresses range from 1.0.0.1 to 223.255.255.254.

Figure 3-12. Setup – Configure Connection 1 for Static IP for the WAN

To configure the WAN connection for Static, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose.

1.Click the Connection 1 button under WAN Setup to view the default PPPoA Connection Setup configuration menu.

2.Select Static from the Type: pull-down menu. This action will change the menu so it offers different settings for configuration.

3.Type in a Name: in the space provided (WAN_PPPoA is used in the above example).

4.If you are told to change the VPI or VCI values, type in the values given to you by your service provider. Many users will be able to use the default settings.

5.Leave the default QoS values if you are unsure or the ISP did not provide this information.

6.Do not change the PCR or SCR values unless you are required to do so. If you are told to change these, type in the values given to you by your service provider.

30

Image 38
Contents DSL-G664T Warnung Table of Contents Advanced Router Management Before You Start Installation RequirementsAbout This User’s Guide Additional Software 802.11b Wireless LAN ConfigurationEthernet Port NIC Adapter About Clip Connections RFCInformation you will need from your Adsl service provider Packing List LAN Subnet Mask for the DSL-G664TRouter Description and Operation What is ADSL?Introduction Router Features Standards Compatibility and Compliance Packing List Front Panel DisplayRear Panel Connections Wireless LAN Basics Introduction to 802.11b Wireless802.11g Wireless Radio TransmissionAdsl Technology RangeHardware Installation LocationPower on Router Factory Reset ButtonConnect Adsl Line Hub or Switch to Router ConnectionNetwork Connections Connect Router to EthernetComputer to Router Connection WAN Configuration Summary Basic Router ConfigurationConfiguring IP Settings on Your Computer Configure Windows XP for Dhcp Windows Windows ME Configure Windows 2000 for DhcpConfigure Windows ME for Dhcp Windows 95 and Windows Windows NT 4.0 Workstations Configure Windows 95 and Windows 98 for DhcpConfigure Windows NT 4.0 for Dhcp Access the Configuration Manager Login to HomeConfigure the Router Home Status Information windowSetup Menu Opening Setup windowWireless Settings Wireless configuration windowWireless Security WEP configuration window1X configuration window 802.1XWPA Wi-Fi Protected Access PSK StringModem Setup Modem Setup menu change modulation typeConfigure Connection 1 for PPPoA PPPoA Connection 1 Setup menuConfigure Connection 1 for PPPoE Change the Connection Type10. Setup Configure Connection 1 for PPPoE Configure Connection 1 for Bridge 11. Setup Configure Connection 1 for BridgeConfigure Connection 1 for Static IP for WAN 12. Setup Configure Connection 1 for Static IP for the WANPage Configure Connection 1 for Dhcp for WAN Configure Connection 1 for Clip 14. Setup Configure Connection 1 for Clip IPoACreate a New Connection New Connection Example 1 Create a New PPPoE Connection16. Set up a New Connection Connection New Connection Example 2 Create a New Bridge ConnectionEnd IP Dhcp Configuration for LANDhcp Parameter Description Start IP Lease TimeEnable Dhcp Relay 18. Configure Dhcp Relay Service19. Configure Management IP Management IPSave Configuration Changes 20. Router Tools Menus22. Changes permanently saved message Advanced setup main menu Advanced Router ManagementUPnP Advanced UPnP windowLAN Clients Setup LAN ClientsPort Forwarding Advanced Port Forwarding windowApplications Category Available Rules GamesAudio/Video ServersSet up Custom Port Forwarding Rules Page Access Control Access Control menuVPN DMZ IP Address Enable/Disable NAT and FirewallAdvanced Security Setup Remote Management Bridge FiltersMulticast Pass-through 10. Multicast pass-through menuStatic Routing 11. Static Routing menuDynamic Routing 12. Dynamic Routing RIP menuWireless Management Multiple Virtual ConnectionsPage Tools and Utility Menus 13. Tools and utility menu linksUser Management 14. User Management menuSystem Commands 15. Tools System Commands menuRemote Log 16. Remote Log menuUpdate Gateway 17. Tools Update Gateway windowPing Test 18. Tools Ping Test windowModem Test 19. Tools Modem Test windowStatus Menus 20. Status display linksNetwork Statistics 21. Network Statistics windowConnection Status 22. Connection Status windowDhcp Clients 23. Dhcp Clients windowModem Status 24. Modem Status windowProduct Information 25. Product Information windowSystem Log 26. System Log windowHelp Menu 27. Opening Help windowTechnical Specifications Physical and Environmental CE Class BAssigning Network IP Addresses IP Address SetupUsing the Default IP Address Manual IP Address AssignmentChanging the IP Address of the Router Using DhcpIP Setup Example #2 IP Concepts IP AddressesSubnet Mask Class Beginning Address Ending AddressIP Class Subnet Mask Class a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0Microfilters Microfilter InstallationMicrofilters and Splitters Line Splitter Installation Line Splitter