D-Link DSL-G664T Create a New Connection, New Connection Example 1 Create a New PPPoE Connection

Page 42

9.Click the Apply button when you have entered all the information. The web browser will briefly go blank. You are now finished changing setting for the primary WAN connection known as Connection 1. It is now necessary to save the changes you just made and restart the Router.

10.To save the changes made to Connection 1, click the Tools tab and then click on the System Commands button. Click on the Save All button to store the configuration settings. Click on Back button to return to the System Commands menu.

11.Check the WAN connection status. Click the Status tab and then the Connection Status button. Look under WAN to view the State of Connection 1, it should read “ N/A”. If the WAN connection state does not appear to Connected after a few minutes, go back to the Connection 1 Setup menu, check the settings and make sure they are correct.

Create a New Connection

An alternative method of changing the connection type used by the Router is to create a new connection. Creating a new connection will not change the Connection 1 settings, it will make a new set of coneciton configuration settings. The new set created will be labeled Connection 2, additional connections created will be likewise labeled Connection 3, Connection 4 and so on. Use the method described here to create up to 8 different connection configuration sets. At any time you may reconfigure the settings for any previously created connection by clicking on the menu button for the connection displayed under the WAN Setup heading.

New Connection Example 1 - Create a New PPPoE Connection

The example below describes how to set up a new connection that uses a PPPoE type WAN conneciton. To create a new connection:

1.Click on the New Connection button.

2.Configure the Router for the Type: of conneciton used and all the remaining settings as discussed in the preceding section. In this example, the type of connection used for Connection 2 is PPPoE. Notice also that the VPI and VCI values have been changed.

3.Click the Apply button to cerate the new connection. Notice that a new menu button is created (Connection 2), this links to the configuration menu for Connection 2 (see example below). If at any time you want to change, delete, disconnect or connect this WAN connection, click on the Connection 2 button.

4.Save the new connection.

Figure 3- 15. Set up a New Connection – Connection 2

34

Image 42
Contents DSL-G664T Warnung Table of Contents Advanced Router Management Installation Requirements About This User’s GuideBefore You Start Additional Software 802.11b Wireless LAN ConfigurationEthernet Port NIC Adapter About Clip Connections RFCInformation you will need from your Adsl service provider Packing List LAN Subnet Mask for the DSL-G664TWhat is ADSL? IntroductionRouter Description and Operation Router Features Standards Compatibility and Compliance Packing List Front Panel DisplayRear Panel Connections Wireless LAN Basics Introduction to 802.11b Wireless802.11g Wireless Radio TransmissionAdsl Technology RangeHardware Installation LocationPower on Router Factory Reset ButtonConnect Adsl Line Hub or Switch to Router ConnectionNetwork Connections Connect Router to EthernetComputer to Router Connection Basic Router Configuration Configuring IP Settings on Your ComputerWAN Configuration Summary Configure Windows XP for Dhcp Windows Configure Windows 2000 for Dhcp Configure Windows ME for DhcpWindows ME Windows 95 and Windows Configure Windows 95 and Windows 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Access the Configuration Manager Login to HomeConfigure the Router Home Status Information windowSetup Menu Opening Setup windowWireless Settings Wireless configuration windowWireless Security WEP configuration window1X configuration window 802.1XWPA Wi-Fi Protected Access PSK StringModem Setup Modem Setup menu change modulation typeConfigure Connection 1 for PPPoA PPPoA Connection 1 Setup menuConfigure Connection 1 for PPPoE Change the Connection Type10. Setup Configure Connection 1 for PPPoE Configure Connection 1 for Bridge 11. Setup Configure Connection 1 for BridgeConfigure Connection 1 for Static IP for WAN 12. Setup Configure Connection 1 for Static IP for the WANPage Configure Connection 1 for Dhcp for WAN Configure Connection 1 for Clip 14. Setup Configure Connection 1 for Clip IPoACreate a New Connection New Connection Example 1 Create a New PPPoE Connection16. Set up a New Connection Connection New Connection Example 2 Create a New Bridge ConnectionEnd IP Dhcp Configuration for LANDhcp Parameter Description Start IP Lease TimeEnable Dhcp Relay 18. Configure Dhcp Relay Service19. Configure Management IP Management IPSave Configuration Changes 20. Router Tools Menus22. Changes permanently saved message Advanced setup main menu Advanced Router ManagementUPnP Advanced UPnP windowLAN Clients Setup LAN ClientsPort Forwarding Advanced Port Forwarding windowApplications Category Available Rules GamesAudio/Video ServersSet up Custom Port Forwarding Rules Page Access Control Access Control menuVPN Enable/Disable NAT and Firewall Advanced SecurityDMZ IP Address Setup Remote Management Bridge FiltersMulticast Pass-through 10. Multicast pass-through menuStatic Routing 11. Static Routing menuDynamic Routing 12. Dynamic Routing RIP menuWireless Management Multiple Virtual ConnectionsPage Tools and Utility Menus 13. Tools and utility menu linksUser Management 14. User Management menuSystem Commands 15. Tools System Commands menuRemote Log 16. Remote Log menuUpdate Gateway 17. Tools Update Gateway windowPing Test 18. Tools Ping Test windowModem Test 19. Tools Modem Test windowStatus Menus 20. Status display linksNetwork Statistics 21. Network Statistics windowConnection Status 22. Connection Status windowDhcp Clients 23. Dhcp Clients windowModem Status 24. Modem Status windowProduct Information 25. Product Information windowSystem Log 26. System Log windowHelp Menu 27. Opening Help windowTechnical Specifications Physical and Environmental CE Class BAssigning Network IP Addresses IP Address SetupUsing the Default IP Address Manual IP Address AssignmentUsing Dhcp IP Setup Example #2Changing the IP Address of the Router IP Concepts IP AddressesSubnet Mask Class Beginning Address Ending AddressIP Class Subnet Mask Class a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0Microfilter Installation Microfilters and SplittersMicrofilters Line Splitter Installation Line Splitter