D-Link DSL-G664T manual Multicast Pass-through, Multicast pass-through menu

Page 60

Multicast Pass-through

Multicast pass-through can be enabled or disabled for any WAN connection. When enabled it allows IGMP packets to pass through the WAN interface. IGMP packets are used to control multicasts and discontinue multicasts to individual IP addresses when they are no longer needed.

Figure 4-10. Multicast pass-through menu

To enable Multicast pass through for any WAN connection, select the connection and click the Enable IGMP Multicast box to select the option, then click the Apply button. Remember to save the configuration changes.

52

Image 60

Contents DSL-G664T Warnung Table of Contents Advanced Router Management Installation Requirements About This User’s GuideBefore You Start 802.11b Wireless LAN Configuration Ethernet Port NIC AdapterAdditional Software About Clip Connections RFCInformation you will need from your Adsl service provider Packing List LAN Subnet Mask for the DSL-G664TWhat is ADSL? IntroductionRouter Description and Operation Router Features Standards Compatibility and Compliance Packing List Front Panel DisplayRear Panel Connections Introduction to 802.11b Wireless 802.11g WirelessWireless LAN Basics Radio TransmissionAdsl Technology RangeHardware Installation LocationPower on Router Factory Reset ButtonHub or Switch to Router Connection Network ConnectionsConnect Adsl Line Connect Router to EthernetComputer to Router Connection Basic Router Configuration Configuring IP Settings on Your ComputerWAN Configuration Summary Configure Windows XP for Dhcp Windows Configure Windows 2000 for Dhcp Configure Windows ME for DhcpWindows ME Windows 95 and Windows Configure Windows 95 and Windows 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Access the Configuration Manager Login to HomeConfigure the Router Home Status Information windowSetup Menu Opening Setup windowWireless Settings Wireless configuration windowWireless Security WEP configuration window1X configuration window 802.1XWPA Wi-Fi Protected Access PSK StringModem Setup Modem Setup menu change modulation typeConfigure Connection 1 for PPPoA PPPoA Connection 1 Setup menuConfigure Connection 1 for PPPoE Change the Connection Type10. Setup Configure Connection 1 for PPPoE Configure Connection 1 for Bridge 11. Setup Configure Connection 1 for BridgeConfigure Connection 1 for Static IP for WAN 12. Setup Configure Connection 1 for Static IP for the WANPage Configure Connection 1 for Dhcp for WAN Configure Connection 1 for Clip 14. Setup Configure Connection 1 for Clip IPoACreate a New Connection New Connection Example 1 Create a New PPPoE Connection16. Set up a New Connection Connection New Connection Example 2 Create a New Bridge ConnectionDhcp Configuration for LAN Dhcp Parameter Description Start IPEnd IP Lease TimeEnable Dhcp Relay 18. Configure Dhcp Relay Service19. Configure Management IP Management IPSave Configuration Changes 20. Router Tools Menus22. Changes permanently saved message Advanced setup main menu Advanced Router ManagementUPnP Advanced UPnP windowLAN Clients Setup LAN ClientsPort Forwarding Advanced Port Forwarding windowCategory Available Rules Games Audio/VideoApplications ServersSet up Custom Port Forwarding Rules Page Access Control Access Control menuVPN Enable/Disable NAT and Firewall Advanced SecurityDMZ IP Address Setup Remote Management Bridge FiltersMulticast Pass-through 10. Multicast pass-through menuStatic Routing 11. Static Routing menuDynamic Routing 12. Dynamic Routing RIP menuWireless Management Multiple Virtual ConnectionsPage Tools and Utility Menus 13. Tools and utility menu linksUser Management 14. User Management menuSystem Commands 15. Tools System Commands menuRemote Log 16. Remote Log menuUpdate Gateway 17. Tools Update Gateway windowPing Test 18. Tools Ping Test windowModem Test 19. Tools Modem Test windowStatus Menus 20. Status display linksNetwork Statistics 21. Network Statistics windowConnection Status 22. Connection Status windowDhcp Clients 23. Dhcp Clients windowModem Status 24. Modem Status windowProduct Information 25. Product Information windowSystem Log 26. System Log windowHelp Menu 27. Opening Help windowTechnical Specifications Physical and Environmental CE Class BIP Address Setup Using the Default IP AddressAssigning Network IP Addresses Manual IP Address AssignmentUsing Dhcp IP Setup Example #2Changing the IP Address of the Router IP Concepts IP AddressesSubnet Mask Class Beginning Address Ending AddressIP Class Subnet Mask Class a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0Microfilter Installation Microfilters and SplittersMicrofilters Line Splitter Installation Line Splitter