D-Link DSL-500T manual Power on Router, Factory Reset Button

Page 18

DSL-500T ADSL Router User’s Guide

2

Hardware Installation

Place the Router in a location where it can be easily connected to the various devices as well as to a power source. The Router should not be located where it will be exposed to moisture or excessive heat. Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. As with any electrical appliance, observe common sense safety procedures.

The Router can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.

Power on Router

CAUTION: The Router must be used with the power adapter included with the device.

To power on the Router:

1.Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source.

2.You should see the Power LED indicator light up and remain lit. The Status LED should light solid green and begin to blink after a few seconds.

3.If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED indicators to make sure the connection is valid. The Router will attempt to establish the ADSL connection, if the ADSL line is connected and the Router is properly configured this should light up after several seconds. If this is the first time installing the device, some settings may need to be changed before the Router can establish a connection.

Factory Reset Button

The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on. Use a ballpoint or paperclip to gently push down the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The factory default IP address of the Router is 192.168.1.1 and the subnet mask is 255.255.255.0, the default management Username is admin and the default Password is admin.

6

Image 18
Contents DSL-500T Adsl Router User’s Guide DSL-500T DSL Router User’s Guide FCC WarningWichtige Sicherheitshinweise Warranties ExclusiveHardware SoftwareWarranty and Registration Information for USA Only DSL-500T DSL Router User’s Guide Table of Contents Update Gateway Ping Test OAM Test Installation Requirements About This User’s GuideBefore You Start Ethernet Port NIC Adapter Additional SoftwareAbout Clip Connections RFC Information you will need from your Adsl service provider Information you will need about your LAN or computer What is ADSL? Router Description and OperationRouter Features Standards Compatibility and Compliance Front Panel Display Packing ListRear Panel Connections Power on Router Factory Reset ButtonConnect Adsl Line Hub or Switch to Router ConnectionNetwork Connections Connect Router to EthernetComputer to Router Connection Configuring IP Settings on Your Computer Wan Configuration SummaryConfigure Windows XP for Dhcp DSL-500T Adsl Router User’s Guide Configure Windows 2000 for Dhcp WindowsConfigure Windows ME for Dhcp Windows MEWindows 95 and Windows Configure Windows 95 and Windows 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Access the Configuration Manager Login to HomeConfigure the Router Home Status Information windowSetup Menu Opening Setup windowDSL Modulation Settings DSL Setup menu change modulation typeConfigure Connection 1 for PPPoA PPPoA Connection 1 Setup menuConfigure Connection 1 for PPPoE Change the Connection TypeConfigure Connection 1 for Bridge Setup Configure Connection 1 for Bridge Configure Connection 1 for Static IP for WAN Setup Configure Connection 1 for Static IP for the WANConfigure Connection 1 for Dhcp for WAN Setup Configure Connection 1 for Dhcp service for the WANConfigure Connection 1 for Clip 10. Setup Configure Connection 1 for Clip IPoACreate a New Connection 11. Setup a New Connection Connection New Connection Example 1 Create a New PPPoE Connection12. Setup a New Connection Connection New Connection Example 2 Create a New Bridge ConnectionEnd IP Dhcp Configuration for LANDhcp Parameter Description Start IP Lease TimeEnable Dhcp Relay 14. Configure Dhcp Relay Service15. Configure Management IP Management IPSave Configuration Changes 16. Router Tools Menus17. Available System Commands Advanced Router Management UPnP Advanced UPnP windowLAN Clients Setup LAN ClientsPort Forwarding Advanced Port Forwarding windowApplications Category Available Rules GamesAudio/Video ServersSet up Custom Port Forwarding Rules Port Forwarding User Rules Management Access Control Access Control menuVPN Enable/Disable NAT and Firewall Advanced SecuritySetup Remote Management Bridge FiltersDMZ IP Address Multicast Pass-through 10. Multicast pass-through menuStatic Routing 11. Static Routing menuDynamic Routing 12. Dynamic Routing RIP menuMultiple Virtual Connections Tools and Utility Menus 13. Tools and utility menu linksUser Management 14. User Management menuSystem Function Description Save All System CommandsRestore RestartRemote Log 16. Remote Log menuUpdate Gateway 17. Tools Update Gateway windowPing Test 18. Tools Ping Test windowOAM Test 19. Tools OAM Test windowStatus Menus 20. Status display linksNetwork Statistics 21. Network Statistics windowConnection Status Dhcp ClientsModem Status Product InformationSystem Log Help MenuData Transfer StandardsProtocols RatePhysical and Environmental FCC Class B, CE Class BUsing the Default IP Address Assigning Network IP AddressesManual IP Address Assignment Using Dhcp IP Setup Example #2Changing the IP Address of the Router IP Concepts IP AddressesIP Network Classes Class Beginning Address Ending AddressSubnet Mask IP Class Subnet MaskMicrofilter Installation MicrofiltersLine Splitter Installation Line SplitterPage Offices Japan Link Japan Link U.S.A Registration Card