NETGEAR NTGWGR614 manual MAC Addresses and Address Resolution Protocol, Related Documents

Page 95

Reference Manual for Cable/DSL Wireless Router WGR614

This scheme offers the additional benefit of firewall-like protection because the internal LAN addresses are not available to the Internet through the translated connection. All incoming inquiries are filtered out by the router. This filtering can prevent intruders from probing your system. However, using port forwarding, you can allow one PC (for example, a Web server) on your local network to be accessible to outside users.

MAC Addresses and Address Resolution Protocol

An IP address alone cannot be used to deliver data from one LAN device to another. To send data between LAN devices, you must convert the IP address of the destination device to its media access control (MAC) address. Each device on an Ethernet network has a unique MAC address, which is a 48-bit number assigned to each device by the manufacturer. The technique that associates the IP address with a MAC address is known as address resolution. Internet Protocol uses the Address Resolution Protocol (ARP) to resolve MAC addresses.

If a device sends data to another station on the network and the destination MAC address is not yet recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network receive and read the request. The destination IP address for the chosen station is included as part of the message so that only the station with this IP address responds to the ARP request. All other stations discard the request.

Related Documents

The station with the correct IP address responds with its own MAC address directly to the sending device. The receiving station provides the transmitting station with the required destination MAC address. The IP address data and MAC address data for each station are held in an ARP table. The next time data is sent, the address can be obtained from the address information in the table.

For more information about address assignment, refer to the IETF documents RFC 1597, Address Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP Address Space.

For more information about IP address translation, refer to RFC 1631, The IP Network Address Translator (NAT).

Network, Routing, Firewall, and Basics

B-9

Image 95
Contents Reference Manual for Cable/DSL Wireless Router WGR614 Trademarks World Wide Web This page intentionally left blank Contents Chapter Wireless Configuration Chapter Troubleshooting Appendix C Preparing Your Network Glossary Contents Typographical Conventions Preface About This ManualAudience Special Message Formats Chapter Introduction Key Features of the RouterPowerful, True Firewall with Content Filtering 802.11g Wireless NetworkingExtensive Protocol Support SecurityAutosensing Ethernet Connections with Auto Uplink Maintenance and Support Easy Installation and ManagementPackage Contents LED Descriptions Router’s Front PanelWGR614 Rear Panel Router’s Rear PanelReference Manual for Cable/DSL Wireless Router WGR614 Cabling and Computer Hardware Requirements Chapter Connecting the Router to the InternetWhat You Will Need Before You Begin Where Do I Get the Internet Configuration Parameters? Computer Network Configuration RequirementsInternet Configuration Requirements Record Your Internet Connection Information Connect the router to your network Connecting the WGR614Connecting the Router Which Log in to the router Log in to the routerConnect to the Internet Login windowPPPoE Smart Wizard-Detected Option Setup Smart Wizard menu for PPPoE accountsTelstra Bigpond Cable Smart Wizard-Detected Option Setup Smart Wizard menu for Telstra Bigpond Cable accountsDynamic IP Smart Wizard-Detected Option Setup Smart Wizard menu for Dynamic IP address accountsFixed IP Account Smart Wizard-Detected Option Click Apply to save the settingsISP Does Not Require Login ISP Does Require Login How to Manually Configure Your Internet ConnectionReference Manual for Cable/DSL Wireless Router WGR614 12 Basic Settings ISP list Observe Performance, Placement, and Range Guidelines Chapter Wireless ConfigurationWGR614 Implement Appropriate Wireless SecurityWireless Settings menu Understanding Wireless SettingsReference Manual for Cable/DSL Wireless Router WGR614 Authentication Scheme Selection Understanding WEP Authentication and EncryptionFeature Default Factory Settings Default Factory SettingsWEP Encryption Keys Before You Change the Ssid and WEP SettingsHow to Set Up and Test Basic Wireless Connectivity How to Restrict Wireless Access by MAC Address Wireless Card Access List Setup Wireless Settings encryption menu How to Configure WEPReference Manual for Cable/DSL Wireless Router WGR614 Content Filtering Overview Chapter Content FilteringBlock Sites menu Blocking Access to Internet SitesBlock Services menu Blocking Access to Internet ServicesAdd Services menu Configuring a User Defined ServiceConfiguring Services Blocking by IP Address Range Scheduling When Blocking Will Be EnforcedLogs menu Viewing Logs of Web Access or Attempted Web AccessEmail menu Configuring E-Mail Alert and Web Access Log NotificationsReference Manual for Cable/DSL Wireless Router WGR614 Viewing Router Status Information Chapter MaintenanceThis screen shows the following parameters Renew Click the Renew button to renew the Dhcp lease This screen shows the following statisticsShow Statistics action buttons are described in Table Upgrading the Router Software Viewing a List of Attached DevicesRouter Upgrade menu Configuration File ManagementSettings Backup menu Restoring and Backing Up the ConfigurationErasing the Configuration Changing the Administrator PasswordConfiguring Port Forwarding to Local Servers Chapter Advanced ConfigurationEditing or Deleting a Port Forwarding Entry Adding a Port Forwarding Custom ServiceMultiple Computers for Half Life, Kali or Quake III Example Local Web and FTP Server ExampleConnect Automatically, as Required Configuring WAN Setup OptionsDisable SPI Firewall Setting Up a Default DMZ ServerRespond to Ping on Internet WAN Port Setting the MTU SizeUsing a Dynamic DNS Service LAN IP Setup Menu Using LAN IP Setup OptionsUsing the Router as a Dhcp server Using Address Reservation Static Route Summary Table How to Configure Static RoutesClick the Add button to open the Add/Edit Menu, shown below Enabling Remote Management Access Using Universal Plug and Play UPnP Reference Manual for Cable/DSL Wireless Router WGR614 Basic Functioning Chapter TroubleshootingPower LED Not On LAN or WAN Port LEDs Not On LEDs Never Turn OffTroubleshooting the Web Configuration Interface Troubleshooting the ISP Connection Testing the LAN Path to Your Router Troubleshooting a TCP/IP Network Using a Ping UtilityTesting the Path from Your PC to a Remote Device Problems with Date and Time Restoring the Default Configuration and PasswordReference Manual for Cable/DSL Wireless Router WGR614 TCP/IP, RIP-1, RIP-2, Dhcp Appendix a Technical SpecificationsWireless Related Publications Basic Router Concepts Appendix B Network, Routing, Firewall, and BasicsRouting Information Protocol What is a Router?IP Addresses and the Internet Three Main Address Classes Equals NetmaskExample of Subnetting a Class B Address Subnet AddressingNetmask Notation Translation Table for One Octet Private IP Addresses Single IP Address Operation Using NAT Single IP Address Operation Using NATRelated Documents MAC Addresses and Address Resolution ProtocolDomain Name Server IP Configuration by DhcpInternet Security and Firewalls Stateful Packet Inspection What is a Firewall?Ethernet Cabling Uplink Switches, Crossover Cables, and MDI/MDIX SwitchingCable Quality Reference Manual for Cable/DSL Wireless Router WGR614 Preparing Your Computers for TCP/IP Networking Appendix C Preparing Your NetworkInstall or Verify Windows Networking Components Configuring Windows 95, 98, and Me for TCP/IP NetworkingReference Manual for Cable/DSL Wireless Router WGR614 Choose Settings, and then Control Panel Enabling Dhcp to Automatically Configure TCP/IP SettingsPrimary Network Logon is set to Windows logon Verifying TCP/IP Properties Selecting Windows’ Internet Access MethodConfiguring Windows NT4, 2000 or XP for IP Networking Locate your Network Neighborhood icon Dhcp Configuration of TCP/IP in Windows XP, 2000, or NT4Dhcp Configuration of TCP/IP in Windows XP Reference Manual for Cable/DSL Wireless Router WGR614 Dhcp Configuration of TCP/IP in Windows Reference Manual for Cable/DSL Wireless Router WGR614 Obtain an IP address automatically is selected Dhcp Configuration of TCP/IP in Windows NT4 Reference Manual for Cable/DSL Wireless Router WGR614 TCP/IP Properties dialog box now displays Verifying TCP/IP Properties for Windows XP, 2000, and NT4MacOS Configuring the Macintosh for TCP/IP NetworkingMacOS 8.6 or Verifying TCP/IP Properties for Macintosh Computers Verifying the Readiness of Your Internet Account Are Login Protocols Used?What Is Your Configuration Information? Select the Gateway tab Reference Manual for Cable/DSL Wireless Router WGR614 Restarting the Network This page intentionally left blank Infrastructure Mode Appendix D Wireless Networking BasicsWireless Networking Overview Network Name Extended Service Set Identification Essid Ad Hoc Mode Peer-to-Peer WorkgroupAuthentication Authentication and WEPOpen System Authentication Steps Overview of WEP Parameters Shared Key Authentication StepsKey Size WEP Configuration Options Wireless ChannelsRadio frequency channels used are listed in Table List of Glossary Terms GlossaryAdsl CRL Encapsulating Security Payload Internet service provider Megabits per second NAT Public Switched Telephone Network Ssid UTP Wins Reference Manual for Cable/DSL Wireless Router WGR614 Numerics IndexIetf B-1 RFC Index
Related manuals
Manual 2 pages 18.14 Kb Manual 2 pages 19.81 Kb Manual 2 pages 35.47 Kb