Linksys WAP54G manual Confirm New Settings Screen

Page 22

Wireless-G Access Point

2.Press the Access Point’s orange Cisco logo on its front panel. When the logo turns white and begins to flash, press the SecureEasySetup button on another device. The Access Point’s Cisco logo will stop flashing when the device has been added to the network. Then repeat this procedure for each additional SecureEasySetup device.

When you have finished configuring the devices in your wireless network, click the Next button to continue.

NOTE: You can only add one SecureEasySetup device at a time.

Figure 5-14: Configure Wireless Settings Screen

3. The Setup Wizard will ask you to review your settings before it saves them.

NOTE: Write down these settings. You may need to manually configure non-SecureEasySetup devices in the future.

Click the Yes button if you are satisfied with your settings, or click the No button if you do not want to save your new settings.

Figure 5-15: Confirm New Settings Screen

Chapter 5: Setting up the Wireless-G Access Point

15

Using the Setup Wizard

Image 22

Contents 802 GHz .11g Wireless- G How to Use this User Guide Copyright and TrademarksTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions Front Panel Back Panel25 Congratulations Screen Site Survey Screen Introduction WelcomeWhat’s in this User Guide? Wireless-G Access Point Network Topology Planning Your Wireless NetworkRoaming Network Layout Getting to Know the Wireless-G Access Point Cisco logoBack Panel LAN Port Connections for Setup Connecting the Wireless-G Access PointOverview Setting up the Wireless-G Access Point Using the Setup WizardConnect the Network Cable to the Router or Switch Screen Check the Access Point’s Status Screen Password Screen Basic Settings Screen Using the Access Point’s SecureEasySetup Feature 10 SecureEasySetup Screen15 Confirm New Settings Screen Configuring a Non-SecureEasySetup Device 16 Congratulations ScreenManually Configuring the Access Point’s Wireless Settings 17 Configure Wireless Settings ScreenWEP 64-Bit WEP 128-BitWPA Personal WPA2 PersonalLinksys Wireless Guard WPA2 Mixed ModeWPA Enterprise 25 Congratulations Screen Configuring the Linksys Wireless Guard Settings 26 Attention Screen28 Securing Your Access Point Screen 31 Wireless Guard Congratulations Screen Using the Linksys Wireless Guard Service Client Software InstallationExit Other Applications Destination Location Network Access Restart Your ComputerAccessing your Account Your Account11 Network Administration Add a Guest12 Modify Access Control Add a Member Member Registration16 Subscriber Information 18 Credentials Information To unprotect a network Securing or Unprotecting Your Wireless Guard NetworkTo secure an unprotected network Setup Configuring the Wireless-G Access PointNavigating the Utility Administration WirelessStatus Network Setup Accessing the UtilitySetup Network Setup Tab Configuration TypeSetup Static IP Screen AP Mode Setup AP Mode TabLAN MAC Address Configuring the Wireless-G Access Point Setup AP Mode Tab Wireless-G Access Point Wireless Basic Wireless Settings Tab Basic Wireless Settings12 Confirm Reset WPA-Personal Wireless Wireless Security TabWireless Security WPA2-PersonalWPA2-Mixed WPA-EnterpriseRadius Wireless MAC Filter Wireless Wireless MAC Filter TabAccess Restriction Wireless Advanced Wireless Settings Tab Advanced WirelessWireless-G Access Point Backup and Restore Administration Management TabAP’s Password ManagementSnmp V1/V2c Administration Snmp TabSnmp Community Administration Log Tab LogFirmware Upgrade Administration Factory Defaults TabAdministration Firmware Upgrade Tab Factory DefaultsAP’s Information Status Local Network TabLocal Network Status Wireless Network Tab Wireless NetworkAppendix a Troubleshooting Frequently Asked QuestionsWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Security Threats Facing Wireless Networks Wireless-G Access Point Figure C-1 Firmware Upgrade Appendix C Upgrading FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Appendix F Specifications Operating Humidity Appendix G Warranty Information Limited WarrantyAppendix H Regulatory Information FCC StatementNeed to contact Linksys? Appendix I Contact InformationInformation section in this Guide

Related manuals

Manual 2 pages 49.81 Kb