Linksys WAP54G manual Does the Access Point function as a firewall?

Page 67

Wireless-G Access Point

What is a MAC Address?

The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.

How do I avoid interference?

Using multiple Access Points on the same channel and in close proximity to one another will generate interference. When employing multiple Access Points, make sure to operate each one on a different channel (frequency).

How do I reset the Access Point?

Press the Reset button on the back of the Access Point for about ten seconds. This will reset the unit to its default settings.

How do I resolve issues with signal loss?

There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment.

You may also try using different channels, as this may eliminate interference affecting only one channel. Also, open the Access Point’s Web-based Utility. Click the Wireless tab and then the Advanced Wireless tab. Make sure the Output Power is set to 100%.

Does the Access Point function as a firewall?

No. The Access Point is only a bridge from wired Ethernet to wireless clients.

I have excellent signal strength, but I cannot see my network.

Wireless security, such as WEP or WPA, is probably enabled on the Access Point, but not on your wireless adapter (or vice versa). Verify that the same wireless security settings are being used on all devices in your wireless network.

What is the maximum number of users the Access Point can handle?

No more than 65, but this depends on the volume of data and may be fewer if many users create a large amount of network traffic.

Appendix A: Troubleshooting

60

Frequently Asked Questions

Image 67

Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use this User GuideTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions Back Panel Front Panel25 Congratulations Screen Site Survey Screen Welcome IntroductionWhat’s in this User Guide? Wireless-G Access Point Network Topology Planning Your Wireless NetworkRoaming Network Layout Cisco logo Getting to Know the Wireless-G Access PointBack Panel LAN Port Connections for Setup Connecting the Wireless-G Access PointOverview Using the Setup Wizard Setting up the Wireless-G Access PointConnect the Network Cable to the Router or Switch Screen Check the Access Point’s Status Screen Password Screen Basic Settings Screen 10 SecureEasySetup Screen Using the Access Point’s SecureEasySetup Feature15 Confirm New Settings Screen 16 Congratulations Screen Configuring a Non-SecureEasySetup Device17 Configure Wireless Settings Screen Manually Configuring the Access Point’s Wireless SettingsWEP 128-Bit WEP 64-BitWPA2 Personal WPA PersonalLinksys Wireless Guard WPA2 Mixed ModeWPA Enterprise 25 Congratulations Screen 26 Attention Screen Configuring the Linksys Wireless Guard Settings28 Securing Your Access Point Screen 31 Wireless Guard Congratulations Screen Client Software Installation Using the Linksys Wireless Guard ServiceExit Other Applications Destination Location Restart Your Computer Network AccessYour Account Accessing your AccountAdd a Guest 11 Network Administration12 Modify Access Control Member Registration Add a Member16 Subscriber Information 18 Credentials Information To unprotect a network Securing or Unprotecting Your Wireless Guard NetworkTo secure an unprotected network Setup Configuring the Wireless-G Access PointNavigating the Utility Administration WirelessStatus Configuration Type Accessing the UtilitySetup Network Setup Tab Network SetupSetup Static IP Screen AP Mode Setup AP Mode TabLAN MAC Address Configuring the Wireless-G Access Point Setup AP Mode Tab Wireless-G Access Point Basic Wireless Settings Wireless Basic Wireless Settings Tab12 Confirm Reset WPA2-Personal Wireless Wireless Security TabWireless Security WPA-PersonalWPA-Enterprise WPA2-MixedRadius Wireless MAC Filter Wireless Wireless MAC Filter TabAccess Restriction Advanced Wireless Wireless Advanced Wireless Settings TabWireless-G Access Point Management Administration Management TabAP’s Password Backup and RestoreSnmp V1/V2c Administration Snmp TabSnmp Community Log Administration Log TabFactory Defaults Administration Factory Defaults TabAdministration Firmware Upgrade Tab Firmware UpgradeAP’s Information Status Local Network TabLocal Network Wireless Network Status Wireless Network TabFrequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Security Threats Facing Wireless Networks Wireless-G Access Point Appendix C Upgrading Firmware Figure C-1 Firmware UpgradeShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Appendix F Specifications Operating Humidity Limited Warranty Appendix G Warranty InformationFCC Statement Appendix H Regulatory InformationNeed to contact Linksys? Appendix I Contact InformationInformation section in this Guide

Related manuals

Manual 2 pages 49.81 Kb