Linksys WAP54G manual Network Access, Restart Your Computer

Page 35

Wireless-G Access Point

7.The Linksys Wireless Guard client software is successfully installed. Before you can use the program, you must restart your computer. Select Yes to restart your computer now. Select No to restart your computer at a later time. Remove any disks that are in their drives, and then click Finish.

8.After the Linksys Wireless Guard client software is installed, a key icon will be displayed on the right side of the system tray at the bottom of your screen. The color of the key will change according to the status of the network connection. The most common colors are described below.

Green - Connected.

Green with Red X - Connected, but waiting for authentication. Gray - Not connected.

Red - Connected to a network that is not protected by Linksys Wireless Guard.

Network Access

After Linksys Wireless Guard is installed, any time you access a Linksys Wireless Guard protected network, this screen will appear. To access your network, click Login as a Wireless Guard Member, or if you are a guest, click Login as a Wireless Guard Guest. Enter your user name and password, and then click Login.

Login as a Wireless Guard Member. Select this option if you are a registered member.

Login as a Wireless Guard Guest. Select this option if you are a registered guest member. The guest must first be added as a guest at the Membership and Network Administration Website. See the “Add a Guest” section, shown below.

Save Password. Select this if you want the system to remember your password so you don’t have to enter it when you log in.

Enable Auto Login. Select this if you want the system to bypass the login.

Click Cancel to cancel the login, or if you forget your password, click Lost Password.

Chapter 6: Using the Linksys Wireless Guard Service

Figure 6-7: Restart Your Computer

Figure 6-8: The Network Access Screen

28

Network Access

Image 35

Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use this User GuideTable of Contents Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Back Panel Front Panel25 Congratulations Screen Site Survey Screen Welcome IntroductionWhat’s in this User Guide? Wireless-G Access Point Roaming Planning Your Wireless NetworkNetwork Topology Network Layout Cisco logo Getting to Know the Wireless-G Access PointBack Panel LAN Port Overview Connecting the Wireless-G Access PointConnections for Setup Using the Setup Wizard Setting up the Wireless-G Access PointConnect the Network Cable to the Router or Switch Screen Check the Access Point’s Status Screen Password Screen Basic Settings Screen 10 SecureEasySetup Screen Using the Access Point’s SecureEasySetup Feature15 Confirm New Settings Screen 16 Congratulations Screen Configuring a Non-SecureEasySetup Device17 Configure Wireless Settings Screen Manually Configuring the Access Point’s Wireless SettingsWEP 128-Bit WEP 64-BitWPA2 Personal WPA PersonalWPA Enterprise WPA2 Mixed ModeLinksys Wireless Guard 25 Congratulations Screen 26 Attention Screen Configuring the Linksys Wireless Guard Settings28 Securing Your Access Point Screen 31 Wireless Guard Congratulations Screen Client Software Installation Using the Linksys Wireless Guard ServiceExit Other Applications Destination Location Restart Your Computer Network AccessYour Account Accessing your AccountAdd a Guest 11 Network Administration12 Modify Access Control Member Registration Add a Member16 Subscriber Information 18 Credentials Information To secure an unprotected network Securing or Unprotecting Your Wireless Guard NetworkTo unprotect a network Navigating the Utility Configuring the Wireless-G Access PointSetup Status WirelessAdministration Configuration Type Accessing the UtilitySetup Network Setup Tab Network SetupSetup Static IP Screen LAN MAC Address Setup AP Mode TabAP Mode Configuring the Wireless-G Access Point Setup AP Mode Tab Wireless-G Access Point Basic Wireless Settings Wireless Basic Wireless Settings Tab12 Confirm Reset WPA2-Personal Wireless Wireless Security TabWireless Security WPA-PersonalWPA-Enterprise WPA2-MixedRadius Access Restriction Wireless Wireless MAC Filter TabWireless MAC Filter Advanced Wireless Wireless Advanced Wireless Settings TabWireless-G Access Point Management Administration Management TabAP’s Password Backup and RestoreSnmp Community Administration Snmp TabSnmp V1/V2c Log Administration Log TabFactory Defaults Administration Factory Defaults TabAdministration Firmware Upgrade Tab Firmware UpgradeLocal Network Status Local Network TabAP’s Information Wireless Network Status Wireless Network TabFrequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Security Threats Facing Wireless Networks Wireless-G Access Point Appendix C Upgrading Firmware Figure C-1 Firmware UpgradeNetwork Neighborhood/My Network Places Appendix D Windows HelpShared Resources Appendix E Glossary Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Appendix F Specifications Operating Humidity Limited Warranty Appendix G Warranty InformationFCC Statement Appendix H Regulatory InformationInformation section in this Guide Appendix I Contact InformationNeed to contact Linksys?

Related manuals

Manual 2 pages 49.81 Kb