Linksys WRT54G-TM manual Getting to Know the Wireless-G Broadband Router, Back Panel

Page 13

Wireless-G Broadband Router

Chapter 3: Getting to Know the Wireless-G Broadband Router

The Back Panel

The Router's ports, where the cables are connected, are located on the back panel.

	Figure 3-1: The Router’s Back Panel
Reset Button	There are two ways to reset the Router's factory defaults. Either press the Reset Button, for
	approximately five seconds, or restore the defaults from the Administration tab - Factory
	Defaults in the Router's Web-based Utility.
Internet	The Internet port is where you will connect your broadband Internet connection.
1, 2, 3, 4	These ports (1, 2, 3, 4) connect the Router to your networked PCs and other Ethernet network
	devices.

IMPORTANT: Resetting the Router will erase all of your settings (Internet connection, wireless security, and other settings) and replace them with the factory defaults. Do not reset the Router if you want to retain these settings.

Power

The Power port is where you will connect the power adapter.

Chapter 3: Getting to Know the Wireless-G Broadband Router

6

The Back Panel

Image 13

Contents 802 GHz .11g Wireless- G Word definition Copyright and TrademarksTable of Contents Appendix B Wireless Security Appendix a TroubleshootingAppendix C Upgrading Firmware Appendix D Windows Help Router’s Back Panel List of Figures23 Wireless Tab Wireless MAC Filter Wireless-G Broadband Router Welcome IntroductionWhat’s in this User Guide? Wireless-G Broadband Router Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterConnecting Your Network Devices Connecting Another Router Hardware Installation for Connection to Another RouterConnecting Your Network Devices Password Screen Configuring the Wireless-G Broadband RouterInternet Setup Setup Tab Basic SetupPPPoE Connection Type Optional Settings Router IP 12 Setup Tab Ddns Setup Tab Ddns13 Setup Tab MAC Address Clone Setup Tab MAC Address Clone14 Setup Tab Advanced Routing Gateway Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings 17 Wireless Tab Wireless Security WPA Personal Wireless Tab Wireless Security20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius 23 Wireless Tab Wireless MAC Filter Wireless Tab Wireless MAC FilterSetting Wireless Tab Advanced Wireless SettingsWireless-G Broadband Router Security Tab VPN Passthrough Security Tab FirewallTo create an Internet Access policy Access Restrictions Tab Internet AccessTo create an Inbound Traffic policy 33 Applications and Gaming Tab Port Range Forward Applications and Gaming Tab Port Range ForwardPort Triggering Applications & Gaming Tab Port TriggeringApplications and Gaming Tab QoS Applications and Gaming Tab DMZApplication Port Priority Administration Tab Log Administration Tab Management39 Administration Tab Diagnostics Administration Tab DiagnosticsAdministration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management 45 Status Tab Router Status Tab Router46 Status Tab Local Network Status Tab Local Network48 Status Tab Wireless Status Tab WirelessCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Broadband Router Wireless-G Broadband Router Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Power LED keeps flashing Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?What is the Ieee 802.11g standard? What is the Ieee 802.11b standard?What Ieee 802.11b features are supported? What Ieee 802.11g features are supported?What is ad-hoc mode? What is infrastructure mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is a MAC Address? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware TCP/IP Appendix D Windows HelpWindows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router WRT54G Appendix G SpecificationsOperating Temp Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationWireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Dual-Band Wireless Access Point Appendix J Contact Information