Linksys WRT54G-TM manual Wireless-G Broadband Router

Page 33

Wireless-G Broadband Router

Fragmentation Threshold. This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of 2347.

AP Isolation. This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. To use this function, select On. AP Isolation is Off by default.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Chapter 6: Configuring the Wireless-G Broadband Router

26

The Wireless Tab - Advanced Wireless Settings

Image 33

Contents 802 GHz .11g Wireless- G Word definition Copyright and TrademarksTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityAppendix C Upgrading Firmware Appendix D Windows Help Router’s Back Panel List of Figures23 Wireless Tab Wireless MAC Filter Wireless-G Broadband Router Welcome IntroductionWhat’s in this User Guide? Wireless-G Broadband Router Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterConnecting Your Network Devices Connecting Another Router Hardware Installation for Connection to Another RouterConnecting Your Network Devices Password Screen Configuring the Wireless-G Broadband RouterInternet Setup Setup Tab Basic SetupPPPoE Connection Type Optional Settings Router IP 12 Setup Tab Ddns Setup Tab Ddns13 Setup Tab MAC Address Clone Setup Tab MAC Address Clone14 Setup Tab Advanced Routing Gateway Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings 17 Wireless Tab Wireless Security WPA Personal Wireless Tab Wireless Security20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius 23 Wireless Tab Wireless MAC Filter Wireless Tab Wireless MAC FilterSetting Wireless Tab Advanced Wireless SettingsWireless-G Broadband Router Security Tab VPN Passthrough Security Tab FirewallTo create an Internet Access policy Access Restrictions Tab Internet AccessTo create an Inbound Traffic policy 33 Applications and Gaming Tab Port Range Forward Applications and Gaming Tab Port Range ForwardPort Triggering Applications & Gaming Tab Port TriggeringApplications and Gaming Tab QoS Applications and Gaming Tab DMZApplication Port Priority Administration Tab Log Administration Tab Management39 Administration Tab Diagnostics Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management 45 Status Tab Router Status Tab Router46 Status Tab Local Network Status Tab Local Network48 Status Tab Wireless Status Tab WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Broadband Router Wireless-G Broadband Router Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Power LED keeps flashing Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?What is the Ieee 802.11g standard? What is the Ieee 802.11b standard?What Ieee 802.11b features are supported? What Ieee 802.11g features are supported?What is ad-hoc mode? What is infrastructure mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is a MAC Address? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware TCP/IP Appendix D Windows HelpWindows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router WRT54G Appendix G SpecificationsOperating Temp Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationWireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Dual-Band Wireless Access Point Appendix J Contact Information