Linksys WRT54G-TM manual Frequently Asked Questions, Power LED keeps flashing

Page 54

Wireless-G Broadband Router

14.The Power LED keeps flashing.

The Power LED flashes when the device is first powered up. Meantime, the system will boot up itself and check for proper operation. After finishing the checking procedure, the LED stays solid to show that the system is working fine. If the LED keeps flashing after this time, the device is not working properly. Try to

flash the firmware by assigning a static IP address to the computer, and then upgrade the firmware. Try using the following settings, IP Address: 192.168.0.50 and Subnet Mask: 255.255.255.0.

15.When I enter a URL or IP address, I get a time-out error or am prompted to retry.

•Check if other PCs work. If they do, ensure that your workstation’s IP settings are correct (IP Address, Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.

•If the PCs are configured correctly, but still not working, check the Router. Ensure that it is connected and powered on. Connect to it and check its settings. (If you cannot connect to it, check the LAN and power connections.)

•If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Router to verify a direct connection.

•Manually configure the TCP/IP settings with a DNS address provided by your ISP.

•Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab. Make sure that Internet Explorer is set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct connection to the Internet.

Frequently Asked Questions

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

47

Frequently Asked Questions

Page 53 Page 55
Image 54
Page 53 Page 55
Contents 802 GHz .11g Wireless- G Copyright and Trademarks Word definitionTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityAppendix C Upgrading Firmware Appendix D Windows Help List of Figures Router’s Back Panel23 Wireless Tab Wireless MAC Filter Wireless-G Broadband Router Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Broadband Router Back PanelFront Panel DMZConnecting the Wireless-G Broadband Router OverviewConnecting Your Network Devices Hardware Installation for Connection to Another Router Connecting Another RouterConnecting Your Network Devices Configuring the Wireless-G Broadband Router Password ScreenSetup Tab Basic Setup Internet SetupPPPoE Connection Type Optional Settings Router IP Setup Tab Ddns 12 Setup Tab DdnsSetup Tab MAC Address Clone 13 Setup Tab MAC Address CloneSetup Tab Advanced Routing 14 Setup Tab Advanced Routing GatewayWireless Tab Basic Wireless Settings Wireless Tab Wireless Security 17 Wireless Tab Wireless Security WPA Personal20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter 23 Wireless Tab Wireless MAC FilterWireless Tab Advanced Wireless Settings SettingWireless-G Broadband Router Security Tab Firewall Security Tab VPN PassthroughAccess Restrictions Tab Internet Access To create an Internet Access policyTo create an Inbound Traffic policy Applications and Gaming Tab Port Range Forward 33 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Triggering Port TriggeringApplications and Gaming Tab DMZ Applications and Gaming Tab QoSApplication Port Priority Administration Tab Management Administration Tab LogAdministration Tab Diagnostics 39 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management Status Tab Router 45 Status Tab RouterStatus Tab Local Network 46 Status Tab Local NetworkStatus Tab Wireless 48 Status Tab WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Broadband Router Wireless-G Broadband Router Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Where is the Router installed on the network? Frequently Asked QuestionsPower LED keeps flashing Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? What is the Ieee 802.11b standard?What is ad-hoc mode? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is infrastructure mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware Appendix D Windows Help TCP/IPWindows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Appendix G Specifications WRT54GOperating Temp Appendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementWireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Dual-Band Wireless Access Point Appendix J Contact Information
Top Page Image Contents