Linksys WRT54G-TM manual My DSL service’s PPPoE is always disconnecting

Page 53

Wireless-G Broadband Router

•If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

•Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following

IP address settings for the computer you are using: IP Address: 192.168.0.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.0.1

•Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

12.My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet.

•There is a setup option to “keep alive” the connection. This may not always work, so you may need to re- establish connection periodically.

1.To connect to the Router, go to the web browser, and enter http://192.168.0.1 or the IP address of the Router.

2.Enter the password, if asked. (The default password is admin.)

3.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

4.Click the Save Settings button.

5.Click the Status tab, and click the Connect button.

6.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

•Click the Save Settings button to continue.

•If the connection is lost again, follow steps 1- 6 to re-establish connection.

13.I can’t access my e-mail, web or I am getting corrupted data from the Internet.

The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500. For most DSL users, it is strongly recommended to use MTU 1492.

•If you are having some difficulties, perform the following steps:

1.To connect to the Router, go to the web browser, and enter http://192.168.0.1 or the IP address of the Router.

2.Enter the password, if asked. (The default password is admin.)

3.Look for the MTU option, and select Manual. In the Size field, enter 1492.

4.Click the Save Settings button to continue.

•If your difficulties continue, change the Size to different values. Try this list of values, one value at a time, in this order, until your problem is solved:

1462

1400

1362

1300

Appendix A: Troubleshooting

46

Common Problems and Solutions

Page 52 Page 54
Image 53
Page 52 Page 54
Contents 802 GHz .11g Wireless- G Word definition Copyright and TrademarksTable of Contents Appendix C Upgrading Firmware Appendix D Windows Help Appendix a TroubleshootingAppendix B Wireless Security Router’s Back Panel List of Figures23 Wireless Tab Wireless MAC Filter Wireless-G Broadband Router Welcome IntroductionWhat’s in this User Guide? Wireless-G Broadband Router Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterConnecting Your Network Devices Connecting Another Router Hardware Installation for Connection to Another RouterConnecting Your Network Devices Password Screen Configuring the Wireless-G Broadband RouterInternet Setup Setup Tab Basic SetupPPPoE Connection Type Optional Settings Router IP 12 Setup Tab Ddns Setup Tab Ddns13 Setup Tab MAC Address Clone Setup Tab MAC Address Clone14 Setup Tab Advanced Routing Gateway Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings 17 Wireless Tab Wireless Security WPA Personal Wireless Tab Wireless Security20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius 23 Wireless Tab Wireless MAC Filter Wireless Tab Wireless MAC FilterSetting Wireless Tab Advanced Wireless SettingsWireless-G Broadband Router Security Tab VPN Passthrough Security Tab FirewallTo create an Internet Access policy Access Restrictions Tab Internet AccessTo create an Inbound Traffic policy 33 Applications and Gaming Tab Port Range Forward Applications and Gaming Tab Port Range ForwardPort Triggering Applications & Gaming Tab Port TriggeringApplications and Gaming Tab QoS Applications and Gaming Tab DMZApplication Port Priority Administration Tab Log Administration Tab Management39 Administration Tab Diagnostics Administration Tab DiagnosticsAdministration Tab Config Management Administration Tab Factory DefaultsAdministration Tab Firmware Upgrade 45 Status Tab Router Status Tab Router46 Status Tab Local Network Status Tab Local Network48 Status Tab Wireless Status Tab WirelessNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-G Broadband Router Wireless-G Broadband Router Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnecting Power LED keeps flashing Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?What is the Ieee 802.11g standard? What is the Ieee 802.11b standard?What Ieee 802.11b features are supported? What Ieee 802.11g features are supported?What is ad-hoc mode? What is infrastructure mode?What is DSSS? What is FHSS? And what are their differences? What is ISM band?What is Spread Spectrum? What is a MAC Address? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware TCP/IP Appendix D Windows HelpWindows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router WRT54G Appendix G SpecificationsOperating Temp Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationWireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Dual-Band Wireless Access Point Appendix J Contact Information
Top Page Image Contents