Linksys WRT54GX2 manual Wireless Tab Basic Wireless Settings, Wireless Network

Page 26

Wireless-G Broadband Router with SRX200

The Wireless Tab - Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

Wireless Network

Wireless Network Mode. From this drop-down menu, you can select the wireless standards running on your network. If you have both 802.11g and 802.11b devices in your network, keep the default setting, Mixed. If you have only 802.11g devices, select G-Only. If you do not have any 802.11g and 802.11b devices in your network, select Disable. SRX200 works automatically with Mixed or G-Only mode, providing the added bonus of increased speed across your entire network and even greater speed when using SRX-enabled products only.

Wireless Network Name (SSID). The SSID is the network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Figure 5-17: Wireless Tab - Basic Wireless Settings

Wireless Channel. Select the appropriate channel from the list provided to correspond with your network settings. All devices in your wireless network must be broadcast on the same channel in order to function correctly and to avoid interference with other wireless items in your home. In most cases, you should keep the default, Auto, so the Router will automatically use the channel that has the least activity.

Adaptive Channel Expansion. This feature increases the RF (radio frequency) bandwidth, so data rates are increased. The existing 20 MHz bandwidth is increased to up to 40 MHz by combining adjacent channels. In most cases, keep the default setting, Auto, so the Router automatically adjusts the increase depending on the channels available.

Wireless SSID Broadcast. When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router's SSID, keep the default setting, Enable. To be more secure and not broadcast the Router's SSID, then select Disable.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Chapter 5: Configuring the Wireless-G Broadband Router

20

The Wireless Tab - Basic Wireless Settings

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Wireless- G Word definition How to Use This User GuideCopyright and Trademarks Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpRouter’s Side Panel Connect a PC24 Security Tab Firewall Introduction WelcomeWhat’s in this Guide? Wireless-G Broadband Router with SRX200 Ssid your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Broadband an always-on, fast Internet connection Getting to Know the Wireless-G Broadband Router with SRX200Router’s Ports and Reset Button Wireless Router’s LEDsConnecting the Wireless-G Broadband Router with SRX200 OverviewWall-Mount Option Placement OptionsStand Option Configuring the Wireless-G Broadband Router Isp your internet providerInternet Connection Type Setup Tab Basic SetupInternet Setup Static IP Connection Type Pptp Connection Type Router IP Network SetupOptional Settings Packet a unit of data sent over a networkNetwork Address Server Settings Dhcp Time SettingSetup Tab Ddns DdnsSetup Tab MAC Address Clone Mac address the unique address that aAdvanced Routing Setup Tab Advanced RoutingNAT Mode Dynamic Routing16 Setup Tab Advanced Routing NAT Mode Routing Table Wireless Tab Basic Wireless Settings Wireless NetworkEncryption encoding data transmitted in a network Wireless Tab Wireless SecurityWireless Security 20 Wireless Tab Wireless Security WEP Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Broadband Router with SRX200 VPN Pass Through Security Tab FirewallFirewall Block WAN RequestTo create an Internet Access policy Access Restrictions Tab Internet AccessInternet Access Ftp a protocol used to transfer files over a TCP/IP network Url the address of a file located on the InternetPort Range Applications and Gaming Tab Port Range ForwardPort Range Forward Port Triggering Applications and Gaming Tab Port TriggeringApplications and Gaming Tab DMZ Triggered Range and Forwarded RangeInternet Access Priority QoS Quality of ServiceWireless Applications and Gaming Tab QoSSummary Port RangeCancel Changes button UPnP Administration Tab ManagementRouter Password MulticastURL Filter Log Administration Tab LogSystem Log DoS LogTraceroute Test Administration Tab DiagnosticsPing Test Ping ParametersFactory Defaults Administration Tab Factory DefaultsAdministration Tab Firmware Upgrade Upgrade FirmwareRestore Configuration Administration Tab Config ManagementBackup Configuration Internet Connection Status Tab RouterRouter Information Status Tab Local Network Local NetworkStatus Tab Wireless WirelessSystem Performance Internet/WirelessStatus Tab System Performance Wireless-G Broadband Router with SRX200 Need to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions For Windows 98SE, Me, 2000, and XP Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with SRX200 Need to upgrade the firmware To start over, I need to set the Router to factory defaultMy power LED will not stop flashing My DSL service’s PPPoE is always disconnectingMy wireless-G speed seems to be slow Cannot connect to the InternetHow do I turn on SRX on my router? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?Does the Router support ICQ send file? How can I block corrupted FTP downloads?What is DMZ Hosting? What is the Ieee 802.11b standard? What are the advanced features of the Router?What is the Ieee 802.11g standard? Is the Router cross-platform compatible?What is ad-hoc mode? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is infrastructure mode?What is DSSS? What is FHSS? And what are their differences? What is ISM band?What is Spread Spectrum? What is WEP?Have excellent signal strength, but I cannot see my network How do I reset the Router?How do I resolve issues with signal loss? Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Security Threats Facing Wireless Networks Wireless-G Broadband Router with SRX200 Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareNetwork Neighborhood/My Network Places Appendix D Windows HelpShared Resources Figure E-1 IP Configuration Screen Windows 98SE or Me InstructionsWindows 2000 or XP Instructions For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Standards Appendix G SpecificationsModel Appendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementWireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Information section in this Guide Appendix J Contact InformationNeed to contact Linksys?
Top Page Image Contents