Linksys WRT54GX2 manual Network Address Server Settings Dhcp, Time Setting

Page 21

Wireless-G Broadband Router with SRX200

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on your network.

DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don’t want a DHCP server, then click the Disable radio button (no other DHCP features will be available).

Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router’s default IP address is 192.168.1.1, the Starting IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default Starting IP Address is 192.168.1.100.

Maximum Number of DHCP Users. Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.

Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.

IP Address Range. The range of available IP addresses is displayed here.

Static DNS 1-2. The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use another, type that IP Address in one of these fields.

Time Setting

Change the time zone in which your network functions from this pull-down menu. (You can even automatically adjust for daylight savings time.) Then, check Automatically adjust clock for daylight saving changes.

Chapter 5: Configuring the Wireless-G Broadband Router

Figure 5-10: Network Address Server Settings

Figure 5-11: Time Setting

15

The Setup Tab - Basic Setup

Image 21
Contents Wireless- G How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Appendix B Wireless Security Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpConnect a PC Router’s Side Panel24 Security Tab Firewall Welcome IntroductionWhat’s in this Guide? Wireless-G Broadband Router with SRX200 Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Broadband Router with SRX200 Router’s Ports and Reset ButtonBroadband an always-on, fast Internet connection Router’s LEDs WirelessOverview Connecting the Wireless-G Broadband Router with SRX200Placement Options Stand OptionWall-Mount Option Isp your internet provider Configuring the Wireless-G Broadband RouterSetup Tab Basic Setup Internet SetupInternet Connection Type Static IP Connection Type Pptp Connection Type Optional Settings Network SetupRouter IP Packet a unit of data sent over a networkTime Setting Network Address Server Settings DhcpDdns Setup Tab DdnsMac address the unique address that a Setup Tab MAC Address CloneNAT Mode Setup Tab Advanced RoutingAdvanced Routing Dynamic Routing16 Setup Tab Advanced Routing NAT Mode Routing Table Wireless Network Wireless Tab Basic Wireless SettingsWireless Tab Wireless Security Wireless SecurityEncryption encoding data transmitted in a network 20 Wireless Tab Wireless Security WEP Wireless MAC Filter Wireless Tab Wireless MAC FilterAdvanced Wireless Wireless Tab Advanced Wireless SettingsWireless-G Broadband Router with SRX200 Firewall Security Tab FirewallVPN Pass Through Block WAN RequestAccess Restrictions Tab Internet Access Internet AccessTo create an Internet Access policy Url the address of a file located on the Internet Ftp a protocol used to transfer files over a TCP/IP networkApplications and Gaming Tab Port Range Forward Port Range ForwardPort Range Applications and Gaming Tab DMZ Applications and Gaming Tab Port TriggeringPort Triggering Triggered Range and Forwarded RangeWireless QoS Quality of ServiceInternet Access Priority Applications and Gaming Tab QoSPort Range SummaryCancel Changes button Router Password Administration Tab ManagementUPnP MulticastSystem Log Administration Tab LogURL Filter Log DoS LogPing Test Administration Tab DiagnosticsTraceroute Test Ping ParametersAdministration Tab Firmware Upgrade Administration Tab Factory DefaultsFactory Defaults Upgrade FirmwareAdministration Tab Config Management Backup ConfigurationRestore Configuration Status Tab Router Router InformationInternet Connection Local Network Status Tab Local NetworkWireless Status Tab WirelessInternet/Wireless Status Tab System PerformanceSystem Performance Wireless-G Broadband Router with SRX200 Appendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC For Windows 98SE, Me, 2000, and XP Open a command prompt. For Windows 98SE and Me TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with SRX200 My power LED will not stop flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingCannot connect to the Internet My wireless-G speed seems to be slowWhere is the Router installed on the network? Frequently Asked QuestionsHow do I turn on SRX on my router? Is IPSec Pass-Through supported by the Router?How can I block corrupted FTP downloads? Does the Router support ICQ send file?What is DMZ Hosting? What is the Ieee 802.11g standard? What are the advanced features of the Router?What is the Ieee 802.11b standard? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What Ieee 802.11g features are supported?What is ad-hoc mode? What is infrastructure mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Have excellent signal strength, but I cannot see my network Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Security Threats Facing Wireless Networks Wireless-G Broadband Router with SRX200 Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Figure E-1 IP Configuration ScreenFor the Router’s Web-based Utility Windows 2000 or XP InstructionsAppendix F Glossary Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Appendix G Specifications ModelStandards Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationWireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Wireless-G Broadband Router with SRX200 Appendix J Contact Information Need to contact Linksys?Information section in this Guide