EAW Attaching SB730s to SB730s Already Suspended, Attaching KF730s to KF730s Already Suspended

Page 21

6.7.4Attaching SB730s to SB730s Already Suspended

NOTE: SB730s should always be flown tight-packed to each other.

1.Move an SB730 Pallet so its SB730 is positioned under the bottom SB730 of the array.

2.Remove the four Quick Release Pins from the Hinges of the SB730 on the pallet.

3.Lower the array until the bottom SB730 barely touches the SB730 on the Pallet.

4.Slide the four Hinges of the SB730 on the pallet into the suspended SB730’s Hinge Tubes. Align Hole 2 of each Hinge with the Hinge Tube Hole.

5.Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in Step 2) through both. The result will be tight-packed SB730s.

6.Repeat Steps 1 to 5 for additional SB730s.

6.7.5Attaching a KF730 to an SB730 Already Suspended

CAUTION: When attaching Hinges to Hinge Tubes in steps 6 and 9, use the correct holes as determined by the KF730 Wizard or by the user-desired angles to achieve the desired splay angle. Failure to follow this instruction can result in poor acoustical performance.

1.Move a Pallet with the KF730 to be attached to the rigging location.

2.Lift the KF730 enclosure off the pallet and lay it down, positioned so its hinges are on top and the enclosure is directly below the array. The KF730 may be laid on the floor or on a standard road case lid at a comfortable working height.

3.Remove the six Quick Release Pins from the rear Hinges of the KF730.

4.Lower the array until the bottom SB730 barely touches the front of the KF730.

5.Slide the two front Hinges of the KF730 into the suspended SB730’s front Hinge Tubes.

6.Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in Step 2) through both.

7.Employing two people, one lifts the rear of the KF730, rotating it on the attached front Hinges.

8.The second person slides the two rear Hinges of the KF730 into the rear Hinge Tubes of the suspended SB730.

NOTE: It will usually be necessary to nudge the KF730 enclosure being attached backwards to line up its Hinges with the Hinge Tubes on the SB730.

9.Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in step 8) through both.

10.Insert each a Quick Release Pin (removed in step 2) into each of the enclosure’s rear Hinge Tubes as a locking pin. See “Locking Pins” Section 6.4.5.

6.7.6Attaching KF730s to KF730s Already Suspended

CAUTION: When attaching Hinges to Hinge Tubes in steps 5 and 10, use the correct holes as determined by the KF730 Wizard or by the user-desired angles to achieve the desired splay angle. Failure to follow this instruction can result in poor acoustical performance.

1.Move a KF730 Pallet so the top rear Hinges of a KF730 are below the rear Hinge Tubes of the bottom KF730 in the array.

2.Remove the six Quick Release Pins from the rear of the KF730 on the pallet.

3.Lower the array until the rear Hinge Tubes of the bottom suspended KF730 are even with the top of the rear Hinge Tubes of the KF730 on the pallet.

4.Extend and slide the Hinges of the KF730 on the pallet into the suspended KF730’s Hinge Tubes.

NOTE: Bump the array slightly as needed to line up the enclosures so the Hinges slide easily into the Hinge Tubes.

RD0169 (A) KF730 & SB730 OWNER’S MANUAL Page 21 of 28

Page 20 Page 22
Image 21
Page 20 Page 22
Contents EAW Part RD0169 KF730 & SB730 LoudspeakerPage Table of Contents General Precautions Safety PrecautionsRead this First EC Statement of ConformityIntroduction ContentsUnpacking Shipping DamageFill Coverage KF730 Array DesignSubwoofers Ground StackingOther Subwoofers Signal Delay on SubwoofersSignal Processing System Block DiagramArray Operation OverviewAmplifier Gain Settings User AdjustmentsAmplifier Power Requirements KF730 Qty Selecting an Appropriate Amplifier SizeSelecting an Appropriate Amplifier Size Rule Of Thumb Input ConnectionsOperating Limits 1 KF730 Input Connections3 SB730 System Input Connections 2 SB730 Connections4 KF730P Input Connections Wire Gauge+ -- + 5 SB730P Input ConnectionsRigging Rigging WarningsSuspension Load Rating Working Load Limit WLL Attaching Enclosures to the FLY-BAR FLY-BAR Rigging RecommendationsHinge and Hinge Tube Holes Quick Release PinsKF730 and SB730 Hinge and Hinge Tube Holes Locking PinsInitial Rigging Preparation Pallets1 KF730s On KF730 Pallet Suspension Procedures2 SB730s on SB730 Pallet Attaching a KF730 or SB730 to the Fly-BarAttaching SB730s to SB730s Already Suspended Attaching a KF730 to an SB730 Already SuspendedAttaching KF730s to KF730s Already Suspended Ground Stacking Procedures Setting the Tilt Angle for the Entire ArrayStacking With SB730s as the Base Stacking Additional Enclosures SB730 as the base Stacking With the Fly-Bar as the BaseStacking the First Enclosure Fly-Bar as the base Stacking Additional Enclosures Fly-Bar as the base Literature and Specifications Service InformationContacting EAW Operating QuestionsGeneral Service Service and MaintenanceRigging Service Basic Field TroubleshootingMaintenance Eastern Acoustic Works ONE Main Street WHITINSVILLE, MA
Top Page Image Contents