Source Technologies 1352 MICR 40 manual Entering Micr Mode, STF Command, STH Command

Page 23

Section 6: MICR Features

The Audit Menu deals with the optional Audit Trail Report settings. See chapter 7 for more information.

Entering MICR Mode

To print MICR documents, your Secure MICR Printer uses special alphanumeric text commands called MICR Mode commands.

There are two different commands which activate MICR mode printing: &%STFPASSWORD$ and &%STHPASSWORD$. The &%STF is the default command and is recommended for most applications.

To use the &%STF command, it must be entered at the beginning of the job datastream. The &%STH command can be entered anywhere prior to accessing secured resources.

The &%STH command is not as powerful as the &%STF command because it does not set as many parameters for MICR printing. Both commands and descriptions are as follows:

&%STF Command

When entering MICR mode with the &%STF mode, the printer will:

•Check to see if the proper Front Panel Combination has been entered (when enabled).

•Allow access to secure check printing resources such as MICR fonts and secure fonts stored in printer ROM.

•Allow access to protected signatures, overlays, logos and other important resources stored in password protected nonvolatile flash memory.

•Display “MICR Mode Active” on the printer’s front panel.

•Disable the printer’s front panel menu system.

•Set printer resolution to 600 dpi for printing MICR fonts.

•Disable Jam Recovery.

•Set the copies parameter to 1.

•Sets Toner Low Alarm.

•Turn Hex Transfer ON.

NOTE: The &%STF command must be entered at the beginning of the print job before any other print data is received.

&%STH Command

The &%STH command does not set-up the printer for check printing activity as completely as the &%STF command mode. This alternate MICR mode command forces the user to manually program some commands through their host application. It is used when programmers cannot place &%STFPASSWORD$ at the beginning of their job. Use the &%STH command if you experience page ejects while in &%STF mode.

Secure MICR Printer User’s Guide July 2003

Page 19	© Source Technologies
	All rights reserved

Image 23

Contents IBM Infoprint 1352 Micr Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error MessagesPrinter Installation Micr Printing Today Micr OverviewCheck Processing System Micr Overview Design Elements in Detail Paper General Features of Check DesignPosition and Dimension Gauge Micr Check DesignAmount Convenience Amount DuplexingMicr Clear Band Data Elements DateSignature Area Amount In WordsDollars Payee AreaExternal Processing Code EPC Field Position Account Title Memo LineCheck Serial Number Fractional Routing Number Micr Line Auxiliary On-Us Field Positions 65 toOn-Us Field Positions 32 to Routing Field Positions 43 toSample Check Quality Issues Layout WeightMicr Check Stock QualityMoisture Check Stock Security Features Security IssuesSecurity Note Security Issues Secure Fonts Micr FeaturesMicr Mode Micr FontsResource Storage Bi-Directional Feedback@PJL Ustatus Device Micr Menu STH Command Entering Micr ModeSTF Command Smcp PasswordMicr Definition Command SMCPxxxx$ optional Set New Password Command &%STExxxxxxxx$Print Micr CMC7 Font SM7ddd...ddd$ STSPrint Micr E-13B Font SMDddd...ddd$ SMDLoad Flash Resource STLxxxxxyyyyyyzdd....dd Print Secure Numeric Font SMFddd..ddd~Print ICR Secure Numeric Font &%SMIxxxxxx~ Print MicroPrint Line SMMxxxxxxxxx!$Tray Swapping Commands Secure Flash Resource Unlock Command STPxxxxx$Tray Lock Command STTL#$ Tray Unlock Command STTU#$DES and AES Decryption STDON$ Customer Character Conversation Command Special Alert and Custom Beep Command Turning Hex Transfer Off IBM Host Programming Features and ExamplesHex Transfer Turning Hex Transfer OnHex Transfer Examples Micr Mode Command Example NON-NEGOTIABLE STFPASSWORD$ Commands in .1 in order of appearanceExample &%STY2300$ Escape Character TranslationSTY4040$ STY4000$Audit Trail Reports Print Audit Report Audit Report Field Two-MICR Line SMDd..d$ or &%SM7d..d$ Audit Trail Report Command SetEnd Audit Record Audit Report Field One SQ1d..d$Audit Report Field Seven SQ7d..d$ Audit Report Field Four SQ4d..d~Audit Report Field Five SQ5d..d$ Audit Report Field Six SQ6d..d$Sprint Print and Purge Audit Report &%SPURGExx$Spurge Print Audit Report SPRINTxx$SQ6 Start Audit Feedback CommandSQ4 SQ5Audit Trail Commands Example Void SQ6October 5, 2005$ Command terminatorSAR$ SQ1200$200SQ7103345 AM$ SMD...$Msmith See list of Micr Error Messages on following Error MessagesError Message On Display Printed Message Description Action Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$Appendix B CMC7 Micr Font Mapping Command SM7ddd..ddd$Appendix C Secure Numeric Font Mapping Command SMFddd...dd~Example &%SMF$1,123.00~ Will print Appendix D ICR Secure Numeric Font Mapping Command SMIxxxxxx~Description Command Appendix E Micr Mode Command SummaryDescription Command Structure Function Appendix F Audit Report Command SummaryPJL Re-Lock Sequence Appendix G PJL Based Micr CommandsFonts and Secured Resources PJL Unlock SequencePCL Font Call Commands PJL Re-Lock Sequence With a New Password ValuePJL Info Micr Command Cartridge Status = Unknown PCL Macro Call PCL Initial Set-UpPCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check @PJL Enter Language = PCL PJL and PCL commands used to print the sample check